Chicco KEY 2-3 ULTRAFIX Instrucciones De Uso página 20

Ocultar thumbs Ver también para KEY 2-3 ULTRAFIX:
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 21
3. Hold the safety belt and ease it into the
retractor.
How to Fit the Child Car Seat into the Car
without the Child
Carry out operations 1,5,6,7 as described in
the paragraph " How to Fit the Child Car Seat
into the Car and Place the Child into the Child
Car Seat".
When not in use, the child car seat must al-
ways be secured, or stowed into the car's
boot with the seat inclination adjuster handle
completely inserted inside the lower part of
the seat. An unsecured child car seat may be
a source of danger in the event of an accident
or sudden braking
How to Adjust the Height of the headrest
The height of the headrest can be adjusted to
8-positions, to allow you to adjust the child
car seat in the best way, according to the
child's height. Ensure that the child's head is
positioned correctly and that the safety belt is
fastened correctly on its shoulder.
When adjusting the height of the headrest,
remember that the child's ears must not ex-
ceed the height of the headrest, and that the
clamp must be positioned just slightly over
the child's shoulders, in order to ensure that
the safety belt fits over the child's shoulder
correctly (diag. 17).
The adjustment operation may be more diffi-
cult if the child is sitting in the child car seat.
To adjust the headrest:
1. Press the lever located at the rear of the
headrest with one hand, whilst simultane-
ously using the other hand on the seat, as
shown in the diagram (diag. 18).
2. Raise/lower the headrest as necessary
(diag. 19).
3. Release the lever, and continue to raise/
lower the headrest, until a click is heard,
indicating that the headrest is locked into
the desired position.
How to Adjust the Width of the Backrest
The width of the child car seat's backrest can
be adjusted, allowing you to adapt the child
car seat to the size of your child's body.
The adjustment operation may be more diffi-
cult if the child is sitting in the child car seat.
To adjust the width of the backrest, turn the
handle, located at the rear of the child car seat,
with one hand:
• Turning the handle in a clockwise direction:
The side wings move away, and the back-
rest becomes wider (diag. 20).
• Turning the handle in an anti-clockwise di-
rection: The side wings move closer, and the
backrest becomes narrower (diag. 21).
How to Adjust the Inclination of the
Backrest
The backrest of the child car seat is movable,
and it can be adjusted easily to the inclination
of the car seat (diag. 22).
The backrest of the child car seat can be ad-
justed to 3 positions, to allow the child to
travel in the most comfortable position.
Before carrying out any adjustment operations,
remove the child from the child car seat.
To adjust the backrest:
1. Place the child car seat onto a flat surface,
as shown in diag. 23.
2. Press the lock/unlock button, located at the
base of the seat and, at the same time, pull/
push the seat inclination adjuster handle,
until the desired position is reached (diag.
24). Each click corresponds to a position.
WARNING! At the end of the operation, check
that the seat inclination adjuster handle is
locked safely and that the button has clicked
into the correct position.
After carrying out the operations described
above, it is possible to fit the child car seat
into the car, and then place the child onto the
child car seat, securing it correctly as described
above.
WARNING! and that it does not exercise pres-
sure on its neck; if necessary, lower the head-
rest.
WARNING! Check that the car seat safety belt
adjuster is either in a backward position with
respect to the backrest of the car seat (or at
least aligned to it)(see diag. 5).
38 38
How to Remove the Backrest/Seat's Fabric
Cover
The fabric covers of the headrest, backrest
and seat are fixed with Velcro straps and zips,
and therefore, they are easy to remove and
replace.
Backrest
1. Unfasten the headrest' s 2 side zips and
then unfasten the 3 Velcro straps (diag.
25).
2. Unfasten the rear zip completely (diag.
26).
3. Remove the small pillows of the side flaps
(diag. 27).
4. Remove the fabric cover from the frame
(diag. 28).
To replace the fabric cover onto the frame,
repeat operations 1,2,3,4 in the reverse order,
paying special attention that the fabric cover
fits and adheres correctly to the frame.
Seat
The seat is formed of two rigid plastic parts
hooked to each other.
To remove the fabric cover from the seat, it is
first necessary to release the upper part from
the fixed lower part:
1. Place the child car seat onto a flat surface,
as shown in diag. 29. Then pull out the seat
inclination adjuster handle to the second
position, following the instructions con-
tained in the paragraph "How to Adjust the
Inclination of the Backrest".
2. Turn the 4 handles, until they coincide with
the OPEN symbols (diag. 30).
WARNING! At the end of the operation,
check that the small reference circles, lo-
cated on the base, and the handles are
aligned, and that the two parts are cor-
rectly unlocked.
3. Position the child car seat as shown in diag.
31, and raise the backrest to the highest
position.
4. Raise the upper part of the child car seat,
removing at the same time the rear panel
of the backrest (diag. 32).
5. Release the fabric cover, by unfastening the
5 press-studs located on the base (diag.
33).
6. Remove the cover from the upper part of
the seat (diag. 34).
To replace the fabric cover onto the frame:
7. Repeat operations 5,6,7 in the reverse or-
der, ensuring that the fabric cover fits onto
and adheres correctly to the frame, in par-
ticular in the red areas, which coincide with
the lap belt holes.
8. Place the child car seat onto a flat surface,
as shown in diag. 35, and pull out the seat's
inclination handle adjuster to the second
position, following the instructions con-
tained in the paragraph "How to Adjust the
Inclination of the Backrest".
9. Place the child car seat as shown in diag.
36, and raise the backrest to he highest po-
sition.
10. Replace the upper part of the seat onto the
lower fixed part: to insert the upper part
more easily, it is recommended to recline
the upper part during the operation, as
shown in diag. 37.
WARNING! At the end of the operation, check
that the two parts coincide.
11. Re-insert the rear panel between the frame
and the fabric cover (diag. 38).
12. Place the child car seat onto a flat surface,
as shown in diag. 39, and turn the 4 handles
to the CLOSE symbols (diag. 40).
WARNING! At the end of the operation, check
that the small reference circles, located on the
base and the handles, are aligned, and that the
two parts are locked correctly.
How to Release the Backrest /Seat
The child car seat can be used in the car only
WITH the backrest fitted onto the seat cor-
rectly.
The backrest can be released and removed
from the seat ONLY for reasons of space,
when not in use.
To release the backrest from the seat:
1. Place the child car seat onto a flat surface,
as shown in diag. 41.
2. Pull out the seat inclination adjuster handle
to the third position; following the instruc-
Tabla de contenido
loading

Tabla de contenido