Philips DCC300 Instrucciones De Manejo página 5

@
IIUSTALLATION AND
CONNECTIONS
3
ANALOG
IN
ANALOG
OUT
4
DIGITAL
IN
DIGITAL
OUT
Rear pane!:
1
MAINS
Be sure to connect the
unit to
the
correct
mains voltage
via
the
supplied mains
cable
Select the
mains voltage
corresponding to the
local mains
voltage (220-240
V,
1 1
0-120
V)
lnput sockets
(left/right)
for
an
analog audio
signal,
Output sockets
(left/right)
of
an
analog audio
signal
lnput socket for
a digital audio
signal
Output socket of
a digital audio
signal
2
VOLTAGE
SELECTOR
Installation:
WARNING
Do not connect the
set
to the mains until all other
connections have been made and the
mains
voltage
has been checked.
The type plate is located on
the
rear
of the
unit
o
Do not place the'DCC
300'
in
humid,
too warm
or hot areas
(e.g
on top of the
amplif ier), near magnetic
fields (e
g
TV)
or
in
dusty
rooms,
as
this
will
reduce the life of the unit
o
When positioning the unit, put the 'DCC
300' on
the
bottom of the
stack
.
Keep
a
f
ree space of
a
few centimeters
around the unit and
do not cover any vents.
.
After you
have
positioned
the
unit correctly,
it
has
to adapt
to the
new ambient
temperature
Leave the 'DCC 3OO'for
about
30
minutes, to allow possible condensation water to
evaporate
Failure to
f
ollow these instructions
may cause damage
to the electronics!
6
o
Connect
the units
using
the
supplied cables
as
follows:
ANALOG lN
- lnsert the
red plug
to the
R
socket and the
other
plug to
the
L
socket
of
your'DCC 300'.
Insert the
two
other plugs to the
corresponding
sockets
of the
DCC
output
of
your
amplif ier. You can also use the TAPE
or
AUX
outputs of your
amplif
ier.
ANALOG
OUT
- Insert the
red plug to the
R
socket
and the
other
plug to the
L
socket
of
your'DCC 300'
Insert the
two
other plugs to the corresponding sockets
of the DCC input
of your amplifier. You can also use
the
TAPE, CD,
AUX or
TUNER inputs of
your
amplif ier
DIGITAL
lN
- lnsert one plug of
the
cinch
lead
to the
input
socket
of
your 'DCC 300' and
the other
plug
to
the
corresponding digital output socket of
e
g
CD
and
DAT.
DIGITAL
OUT
- This output
supplies
a
digital signal
via an
electrical path; for this
reason it can only
be connected to
a
product with
a
digital input
e.g. amplif ier,
DCC
or
DAT
Use a
cinch lead (not supplied)
with
one cinch plug
on
either
end
.
Select
the
local mains voltage
at
the
rear of
the
'DCC
300'.
o
Connect the smaller plug
of
the supplied
mains cable to the
MAINS socket of the
'DCC 300'
and
the mains plug
to the
wall
outlet.
.
You can now
start the
operation
Enloy yourself
I
A
few recommendations:
o
lf
the unit
is
not
used
for some
time, switch
the unit off and
pull the
mains
plug
out
By doing
this, you
will
protect
it
from
lightning damage
.
When you
pull the mains
plug out, do not take it
by the
cable,
but
by
the connector
shell
.
When you have pulled
the mains plug
out,
do not touch the
two contact pins,
as
the'DCC 300'
needs
a
few
seconds
to
discharge
34