Idiomas disponibles
Idiomas disponibles
Turn the TURBOZONE
TM
wash option off if not loading items
for this option. Always use the Heavy Soil detergent fill
recommendation
with TURBOZONE
TM
wash option. (See
"How much detergent to use" in "Detergent Dispenser"
section.)
Side view of TURBOZONE
TM
wash area
Hi Temp
Select this option to increase the water temperature during the
wash portions of the cycle. Hi Temp wash raises the water
temperature to 145°F (63°C), in the main wash. Heating the water
helps improve washing results. Hi Temp wash is useful when
loads contain tough food soil.
This option may add heat and wash time to the cycle.
NOTE: Hi Temp wash is an option with the SMART WASW M,
Pots Pans, and Normal Wash cycles.
Sani Rinse
Select this option to raise the water temperature
in the final rinse
to approximately
155°F (68°C). Sani Rinse adds heat and time to
the cycle. This high temperature rinse sanitizes your dishes and
glassware in accordance
with NSF/ANSl Standard 184 for
Residential Dishwashers. Certified residential dishwashers are
not intended for licensed food establishments.
NOTE: Sani Rinse is an option with SMART WASH
TM,
Pots Pans,
and Normal Wash cycles. Only these sanitization cycles have
been designed to meet the NSF/ANSI requirements.
Heated Dry
The Heated Dry option in combination
with rinse aid will give you
excellent drying results. The energy to use Heated Dry costs
pennies per cycle. Heated Dry is on when the light is lit on the
Heated Dry button. Be sure to load plastic items in the upper rack
to avoid damage.
You may turn off the Heated Dry option by pressing HEATED DRY
so that the light goes off. However, you will have items in your
dishload that will not be dry at the end of the cycle.
NOTE: The Heated Dry option is used in all cycles except Fast
Wash and Quick Rinse.
Lock On
Use the Lock On to avoid unintended use of the dishwasher
between cycles.
When Lock On is lit, all buttons are disabled.
NOTE: The dishwasher
door can be opened while the controls
are locked.
To turn on the Lock
Press and hold HEATED DRY for 4 seconds. Lock On glows.
If you press any pad while your dishwasher is locked, the light
flashes 3 times.
NOTE: If the Heated Dry option is selected, the light will
temporarily turn off until Lock On glows.
To turn off the Lock
Press and hold HEATED DRY for 4 seconds. The light turns off.
Delay Hours/4 Hour Delay
Select this option to run your dishwasher at a later time or during
off-peak hours. You can add items to the load anytime during the
delay. After adding items, press START/RESUME. Make sure the
door is latched or the delay will not continue.
To delay the start
1. Press the delay button to choose the number of hours
delayed.
2. Select a wash cycle and options.
3. Press START/RESUME.
The dishwasher
starts the cycle in the selected number of hours.
NOTES:
•
To cancel the delay and cycle, press CANCEL/DRAIN.
•
To cancel the delay and start the cycle, press START/
RESUME.
•
On top control models, if the door is not closed within
3 seconds of pressing Start/Resume,
press START/RESUME
again.
Follow the progress of your dishwasher with the Cycle Status
indicators.
o
o
•
WASHING
D£YING
CLEAN
NOTE: The features on your dishwasher may vary from those
shown here.
Clean
Clean glows when a cycle is finished. The light turns off when you
press any button or close the door.
Sanitized
If you select the Sani Rinse option, Sanitized glows when the
Sani Rinse cycle is finished. If your dishwasher
did not properly
sanitize your dishes, the light flashes at the end of the cycle. This
can happen if the cycle is interrupted or the incoming water
temperature is too low. The light turns off when you press any
button or close the door.
17
