Idiomas disponibles
Idiomas disponibles
ENGlIsh
•
Apply only a gentle pressure to the tool. Do not
exert side pressure on the disc.
•
Always install the guard and appropriate disc or
wheel. Do not use excessively worn disc or wheel.
•
Be sure the inner and outer flange are
mounted correctly.
•
Make sure the disc or wheel rotates in the direction
of the arrows on the accessory and the tool.
•
Avoid overloading. Should the tool become hot,
let it run a few minutes under no load condition
to cool the accessory. Do not touch accessories
before they have cooled. The discs become very
hot during use.
•
Never work with the grinding cup without a
suitable protection guard in place.
•
Do not use the power tool with a cut-off stand.
•
Never use blotters together with bonded
abrasive products.
•
Be aware, the wheel continues to rotate after the
tools is switched off.
Proper Hand Position (Fig. G)
WARNING: To reduce the risk of serious personal
injury, ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the side
3
handle
, with the other hand on the body of the tool, as
shown in Figure G.
Fig. G
3
Switches
CAUTION: Hold the side handle and body of the tool
firmly to maintain control of the tool at start up and
during use and until the wheel or accessory stops
rotating. Make sure the wheel has come to a complete
stop be fore laying the tool down.
NoTE: To reduce unexpected tool movement, do not
switch the tool on or off while under load conditions. Allow
the grinder to run up to full speed before touching the work
surface. Lift the tool from the surface before turning the tool
off. Allow the tool to stop rotating before putting it down.
Slider Switch (Fig. A)
DWE4214, DWE4227, DWE4336
WARNING: Before connecting the tool to a power
supply, be sure the slider switch is in the off position
40
by pressing the rear part of the switch and releasing.
Ensure the slider switch is in the off position as
described above after any interruption in power
supply to the tool, such as the activation of a ground
fault interrupter, throwing of a circuit breaker,
accidental unplugging, or power failure. If the slider
switch is locked on when the power is connected, the
tool will start unexpectedly.
To start the tool, slide the ON/OFF slider switch
the front of the tool. To stop the tool, release the ON/OFF
slider switch.
For continuous operation, slide the switch toward the front
of the tool and press the forward part of the switch inward.
To stop the tool while operating in continuous mode, press
the rear part of the slider switch and release.
Paddle Switch (Fig. A)
DWE4212, DWE4314
1. To turn the tool on, push the lock-off lever
the back of the tool, then depress the paddle switch
The tool will run while the switch is depressed.
2. Turn the tool off by releasing the paddle switch.
lock-on Button
NoTE: The DWE4314N does not have this feature.
13
•
The lock-on button
extended use applications. To lock the tool on, depress
the lock-on button when the tool is running. The tool
will continue to run after the paddle switch is released.
To unlock the tool, depress and release the paddle
switch. This will cause the tool to stop.
Trigger Switch (Fig. A)
DWE4315
To turn the tool on, depress lock-off button
11
switch
. The trigger can be feathered as long as the
lock-off button is depressed. The tool will remain running
while the trigger is depressed. Turn the tool off by releasing
the trigger.
Spindle Lock (Fig. B)
1
The spindle lock
is provided to prevent the spindle from
rotating when installing or removing wheels. Operate the
spindle lock only when the tool is turned off, unplugged
from the power supply, and has come to a complete stop.
NOTICE: To reduce the risk of damage to the tool, do
not engage the spindle lock while the tool is operating.
Damage to the tool will result and attached accessory
may spin off possibly resulting in injury.
To engage the lock, depress the spindle lock button
and rotate the spindle until you are unable to rotate the
spindle further.
Surface Grinding, Sanding and Wire
Brushing
CAUTION: Always use the correct guard per the
instructions in this manual.
To perform work on a the surface of a workpiece:
7
toward
9
toward
offers increased comfort in
9
then trigger
8
.
