Idiomas disponibles
Idiomas disponibles
To transport
the washer:
1. If washer will be moved during freezing weather, put in 1 qt
(1 L) of R.V.-type antifreeze in the drum. Run washer on a
Drain & Spin cycle.
2. Unplug the power cord.
3. Disconnect
the drain hose from the drain system and attach
to rear panel clips.
4. Shut off both water faucets.
5. Disconnect
the water inlet hoses from faucets, then drain the
hoses and clip them to the rear panel of the washer.
IMPORTANT: Call for service. Do not reuse transport bolts.
Washer must be transported
in the upright position. To avoid
suspension and structural damage to your washer, it must be
properly set up for relocation by a certified technician.
Reinstalling
the washer
1. Follow the "Installation
Instructions"
to locate, level and
connect the washer.
2. Run the washer through the Normal/Casual
cycle with 1/2the
manufacturer's
recommended
amount of HE detergent for a
medium-size
load, to clean the washer and remove the
antifreeze, if used.
TROUBLESHOOTING
First try the solutions suggested here to possibly avoid the cost of a service call...
Washer
displaying
code message
and tone sounds
•
"F20" (Water Inlet Problem--no
water or insufficient
water supply)
Select STOP twice to cancel the cycle. Unplug washer or
disconnect
power.
Check the following:
Are water faucets completely turned on?
Are screens at inlet hose connection to washer clogged?
Are water inlet hoses kinked?
Are water inlet hoses frozen?
Plug in washer or reconnect power. Re-select cycle and press
START. If the problem remains, call for service.
"F21" (Drain Problem)
Select STOP twice to cancel the cycle. Unplug washer or
disconnect
power.
Check the following:
Is the drain hose kinked?
Is the drain hose frozen?
Is the drain hose clogged?
Is the drain hose more than 96" (2.4 m) above the floor?
Plug in washer or reconnect power. Re-select cycle and press
START. If the problem remains, call for service.
"SUD" (Suds Routine)
When excessive suds are detected, a suds routine
automatically
starts. This routine removes extra suds and
assures proper rinsing of your garments. "SUD" is displayed
during rinsing and at the end of the cycle to inform you that
Suds Routine was activated. Use only HE (High Efficiency)
detergents.
"F22" (Front door lock)
Select STOP twice to cancel the cycle.
Is the washer door firmly shut?
The door must be completely closed for the washer to
operate. The door may look closed, but may not be latched.
Open the door and close firmly.
Were you washing a large load?
Before you close the washer door, check for laundry items
sticking out beyond the door opening. Leave enough space
in the washer to allow the clothes to tumble freely. An
overloaded
basket may keep the door from shutting
completely. Reduce your load size if needed.
Press POWER, re-select cycle and press START.
"F" Codes other than F20, F21 and F22
Select STOP twice to cancel the cycle. Select DRAIN & SPIN
if there is excessive water in the washer.
Re-select cycle and press START. If the problem remains, call
for service.
Washer won't start
Electrical
Shock Hazard
Plug into a grounded
3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension
cord.
Failure to follow these instructions can result in death,
fire, or electrical
shock.
Check the following:
Is the power cord plugged into a grounded 3 prong outlet?
Is the washer door firmly shut?
Has a cycle been selected, but START has not been selected
and held for 1 second?
Was the door open after completion
of last cycle?
Washer
won't fill, wash or rinse
•
Check the following:
Is the power cord plugged into a grounded 3 prong outlet?
Is there power at the plug? Check electrical source or call
electrician.
Are the hot and cold water faucets turned on?
Is the water inlet hose kinked?
Are the water inlet valve screens clogged?
Turn off the water and remove inlet hoses from the washer.
Remove any accumulated
film or particles. Reinstall hoses,
turn water on and check for leaks.
22
