Tabla de contenido
Idiomas disponibles
Idiomas disponibles
1 Socket head wrench
1 Instructions for assembly / operation
Safety notices
LIFE AND RISK OF ACCIDENTS
FOR INFANTS AND CHILDREN!
Never leave children unattended with the pack-
aging material. Suffocation hazard. Keep this
product well away from children. This product
is not a toy.
BEWARE OF ELECTRIC SHOCK!
Leaking or water discharge can lead
to life-threatening danger due to elec-
tric shock. Carefully check that all connections
are watertight. Also ensure that all wires of
electric appliances are correct and have been
securely installed.
CAUTION! RISK OF INJURY! Please ensure
that no parts are damaged and that all parts
are correctly assembled. Incorrect assembly
could lead to injury. Please note that washers
and gaskets are wear parts and therefore will
need to be replaced from time to time.
Damaged parts could impact safety and function.
Be sure all seals are correctly seated.
CAUTION! Be careful not to reverse the hot /
cold water plaque
left = red (hot water),
right = blue (cold water).
CAUTION! DAMAGE TO THE ARTICLE!
Please have all installations performed by
skilled individuals.
Please note that the seals are wear parts and
must be changed from time to time.
Any leakage or sudden escape of water can
cause considerable damage to buildings and
property. All connections must therefore be
checked carefully to ensure that they are tight.
Familiarise yourself prior to installation with all
local conditions, e.g. water connections and
shut-off device.
The product is only suitable for use in rooms in
which a temperature above 0 °C is maintained.
274849_Waschtisch-Armatur_Modell A_Content_ES.indd 15
19
DANGER TO
. The correct position is:
2
Introduction / Safety notices / Installation
Installation
Note: Familiarise yourself with the product prior to
assembly. Carefully read the following assembly in-
structions and safety advice. In the event of incorrect
installation, all warranty claims – particularly in re-
lation to subsequent damage – are excluded.
CAUTION! Before you start installation turn
off the water supply at the mains. Otherwise in-
juries and / or property damage may occur.
CAUTION! Do not twist the connection hoses
or place them under tension.
18
Please note: This step requires a cross-tip
screwdriver, a slotted screwdriver and an
open-ended spanner SW 12 mm.
Follow these steps:
Screw the two flexible connection hoses
tight into the designated female threads of the
fitting
.
9
Note: The two flexible connection hoses
are identical. The flexible connection hose
being screwed into the left borehole on the fit-
ting body will be the hot water hose, the flexible
connection hose
18
borehole will be the cold water hose.
CAUTION! Be sure to only tighten the flexible
connection hoses
18
ers or a wrench. Otherwise the product could be
damaged.
Remove the locknut
and using a screwdriver, screw the threaded
14
bolt
all the way into the designated female
14
threads at the bottom of the fitting
Insert the fitting base seal
at the underside of the fitting
over the opening on your washbasin.
First place the C-sealing washer
washbasin, then the C metal washer
the threaded bolt
14
Now screw the locking nuts
bolts
and tighten with an open-end spanner
14
SW 12 mm until the fitting
on the washbasin.
Loosen the lower part of the eccentric by turn-
ing the upper part of the eccentric
Insert the upper part of the eccentric
er with the top seal into the washbasin drain.
hand
18
18
18
being screwed into the right
hand tight. Do not use pli-
from the threaded bolt
15
.
9
into the groove
11
and place it
9
under the
12
onto
13
.
onto the thread
15
is seated tightly
9
clockwise.
16
togeth-
16
GB
15
09.12.15 16:15
Capítulos
Tabla de contenido
