Idiomas disponibles
Idiomas disponibles
c)
Disconnect the plug from the power source
and/or remove the battery pack, if detachable,
from the power tool before making any adjust-
ments, changing accessories, or storing pow-
er tools. Such precautionary measures reduce
the risk of starting the power tool accidentally.
d)
Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
e)
Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition that
may affect the power tool's operation. If dam-
aged, have the power tool repaired before use.
Many accidents are caused by poorly maintained
power tools.
f)
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g)
Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.
h)
Keep handles and grasping surfaces dry,
clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow for
safe handling and control of the tool in unexpected
situations.
5) Service
a)
Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
WARNING
This power tool generates an electromagnetic field dur-
ing operation. This field can impair active or passive
medical implants under certain circumstances. In or-
der to prevent the risk of serious or deadly injuries, we
recommend that persons with medical implants consult
with their physician and the manufacturer of the medi-
cal implant prior to operating the power tool.
30 | GB
5.2 Safety instructions for scroll saws
• In an emergency, switch the machine off directly and
pull out the mains plug.
• Observe all of these notes before and while working
with the saw.
• Never use the saw to cut firewood.
• The machine is equipped with a safety switch
against reactivation if the voltage drops.
• If an extension cable is required, make sure that its
cross-section is sufficient for the current consump-
tion of the saw. Minimum cross-section 1.5 mm
• Only use the cable drum when unrolled.
• Personnel working on the machine must not be dis-
tracted.
• Under no circumstances should the saw blades be
braked by pushing against the side after switching
off the drive.
• Only install saw blades that are well sharpened, free
of cracks and not deformed.
• Faulty saw blades must be replaced immediately.
• Do not use saw blades that do not correspond to the
characteristics specified in these usage instructions.
• Ensure that all devices that cover the saw blade
work properly.
• Safety equipment on the machine must not be disas-
sembled or made unusable.
• Damaged or faulty protective devices must be re-
placed immediately.
• Do not cut workpieces that are too small in order to
keep them secure in your hands.
• Do not load the machine so much that it comes to
a standstill.
• Always press the workpiece firmly against the work-
ing plate.
• Never remove loose fragments, chips or jammed
wood pieces from the running saw blade.
• Switch off the machine to rectify any faults on the
blocked tool attachment. Pull out the mains plug.
Remove the blockage. Attention! Danger of injury
due to saw blade! Wear protective gloves! Perform
a test run without a workpiece. Make sure that no
unusual noises or vibrations occur. If this is the case,
switch the device off and contact the manufacturer.
• Only carry out modifications, adjustment, measuring
and cleaning work when the engine is switched off.
Pull out the mains plug.
• Before switching on, make sure that keys and adjust-
ing tools are removed.
• Switch off the motor and pull out the mains plug
when leaving the work station.
www.scheppach.com
.
2
