Idiomas disponibles
Idiomas disponibles
[] Troubleshooting
Guide
If the unit does not perform
properly
when operated
as instructed
in this owner's manual, check the following
chart
once before calling for service.
iiiiiiiiiiiiiiiiiiiiiiiiii
....
No power
No picture or sound
• Be sure the power cord is plugged
in.
• If a power failure occurs, unplug
the power cord for 30 minutes to allow the unit to
reset itself.
• Check if the power is on.
• Check the outlet connection.
• Check the antenna
or cable connection
to the main unit.
• When the outside
antenna
is used, check the wire condition
and connection.
• View other TV channels. The problem
might be limited to the broadcasting
station.
• Turn off the power and wait for about
1 minute, then turn it on again.
No color
• Check the antenna
or cable connection
to the main unit.
• When the outside
antenna
is used, check the wire condition
and connection.
• View other TV channels. The problem
might be limited to the broadcasting
station.
• Adjust"COLOR"
in "PICTURE" menu.
Sound OK, picture poor
• Check the antenna
or cable connection
to the main unit.
• When the outside
antenna
is used, check the wire condition
and connection.
• Electrical interference
from nearby appliances
may affect picture quality.
• Adjust"CONTRAST"
and "BRIGHT'in
"PICTURE" menu.
• View other TV channels. The problem
might be limited to the broadcasting
station.
Picture distorted
• When the outside
antenna
is used, check the wire condition
and connection.
• View other TV channels.
The problem
might be limited
to the broadcasting
station.
Weak picture
• Check the antenna
or cable connection
to the main unit.
• When the outside
antenna
is used, check the wire condition
and connection.
• Adjust"CONTRAST"
and "BRIGHT'in
"PICTURE" menu.
• View other TV channels. The problem
might be limited to the broadcasting
station.
Lines or streaks in picture
• When the outside
antenna
is used, check the wire condition
and connection.
• Electrical interference
from nearby appliances
may affect picture quality.
• View other TV channels. The problem
might be limited to the broadcasting
station.
Picture blurred
• When the outside
antenna
is used, check the wire condition
and connection.
• View other TV channels. The problem
might be limited to the broadcasting
station.
Ghosts in picture
• Check the antenna
or cable connection
to the main unit.
• When the outside
antenna
is used, check the wire condition
and connection.
• Electrical interference
from nearby appliances
may affect picture quality.
• View other TV channels. The problem
might be limited to the broadcasting
station.
Bars on TV screen
• When the outside
antenna
is used, check the wire condition
and connection.
• Electrical interference
from nearby appliances
may affect picture quality.
Picture rolls vertically
• When the outside
antenna
is used, check the wire condition
and connection.
• Electrical interference
from nearby appliances
may affect picture quality.
• View other TV channels. The problem
might be limited to the broadcasting
station.
Different
color marks onTV
• Move yourTVaway
from nearby electric
appliances.
Turn offthe
power and wait
screen
30 minutes
before turning
it back on.
• View other TV channels. The problem
might be limited to the broadcasting
station.
Poor reception
on some chan-
• Check the antenna
or cable connection
to the main unit.
nels
• When the outside
antenna
is used, check the wire condition
and connection.
• Electrical interference
from nearby appliances
may affect picture quality.
• View other TV channels.
The problem
might be limited
to the broadcasting
station.
Picture OK, sound poor
• View other TV channels. The problem
might be limited
to the broadcasting
station.
No reception
of digital
signals
• Make sure auto channel scan has been completed
(Refer to"Auto
Channel Scan" on
page 12).
Auto channel
scan must be completed
when you set up the unit for the first time
or move it to a location
where previously
unavailable
channels are broadcast.
• The selected channel
may not be broadcasting.
• When auto channel
scan is interrupted
and not completed,
some channels will not
be received. Make sure to complete
(Refer to"Auto
Channel Scan" on page 12).
EN
