Idiomas disponibles
Idiomas disponibles
ENG
ORIGINAL
NOTICE.
►
Fuel can damage paint and some types of
Be careful not to spill fuel when filling
►
plastic
►
your fuel tank
Damage caused by spilled fuel is
not covered under the warranty.
ENGINE OIL.
Oil is a major factor affecting performance and
►
►
service life
Use 4-stroke automotive detergent
►
oil
Use 4-stroke motor oil that meets or exceeds
the requirements for API service category SJ
or later (or equivalent)
service label on the oil container to be sure it
includes the letters SJ or later (or equivalent)
►
SAE 10W-30 is recommended for general use
►
Other viscosities shown in the chart may be
used when the average temperature in your area
is within the indicated range.
OIL LEVEL CHECK.
►
Check the engine oil level with the engine
stopped and in a level position
oil filler cap/dipstick and wipe it clean
the oil filler cap/dipstick into the oil filler neck as
shown, but do not screw it in, then remove it to
►
check the oil level
If the oil level is near or below
the lower limit mark on the dipstick, fill with the
recommended oil to the upper limit mark (bottom
edge of the oil fill hole)
the oil filler cap/dipstick
a low oil level can cause engine damage
type of damage is not covered by the warranty.
OIL CHANGE.
►
Drain the used oil when the engine is warm
►
Warm oil drains quickly and completely
a suitable container below the engine to catch the
used oil, then remove the oil filler cap/dipstick,
oil drain plug and washer
drain completely, then reinstall the oil drain plug
and a new washer, and tighten the oil drain plug
►
securely
Please dispose of used motor oil in a
manner that is compatible with the environment
►
We suggest you take used oil in a sealed
container to your local recycling center or service
station for reclamation
trash, pour it on the ground, or pour it down a drain
With the engine in a level position, fill with the
►
recommended oil to the upper limit mark (bottom
edge of the oil fill hole) on the dipstick
oil filler cap/dipstick and tighten securely.
►
Always check the API
►
Remove the
►
Insert
Do not overfill
►
►
Reinstall
►
Running the engine with
►
This
►
Place
►
Allow the used oil to
►
Do not throw it in the
►
Install the
INSTALLING THE UNIT.
►
Use the airless spraying unit with a gasoline
engine preferably outdoors
direction into account
that no vapors containing solvents are deposited
in the area of the unit
distance of 3 m between the unit with gasoline
engine and the spray gun
distance of 3 m between the unit with gasoline
engine and the spray gun.
VENTILATION WHEN SPRAYING IN ROOMS.
►
Adequate ventilation must be guaranteed in
order to remove the solvent vapors and the
exhaust fumes of the gasoline engine.
CLEANING THE UNIT WITH SOLVENTS.
►
When cleaning the unit with solvents, the
solvent should never be sprayed or pumped back
into a container with a small opening (bunghole)
►
An explosive gas/air mixture can arise
container must be earthed.
CLEANING THE UNIT.
►
Danger of short-circuits caused by water
ingressing into the electrical equipment of the
gasoline engine
high-pressure or high-pressure steam cleaners.
SETTING-UP ON UNEVEN SURFACES.
►
The front side of the unit must point downwards
to prevent sliding away (15).
HANDLE SLIDING FOR TRANSPORT.
►
To engage the handle, press the buttons on the
sides of the handle and insert the handle (16).
TRANSPORT IN VEHICLE.
►
Push locking pin in the swivel mechanism for the
material feed pump and swivel it to a horizontal
position, ensure that the locking pin locks (17)
the high-pressure hose over the hose rack on the
►
handle (18)
CRANE TRANSPORT.
►
Use the hanging points for crane straps or
ropes (19).
TRANSPORT POSITION.
►
Transport unit only when the material feed pump
is in the horizontal position (20)
English
8
►
Take the wind
►
Then place the unit so
►
Observe a minimum
►
Observe a minimum
►
Never spray down the unit with
Secure the unit with a suitable fastening.
►
Swiveling the
►
The
►
Roll
