Wall Mounting; Intended Use; Assembly And Adjustments - DeWalt DCH614 Manual De Instrucciones

English
3. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. Move the charger and battery pack to a location
where the surrounding air temperature is
approximately 65 °F – 75 °F (18 °C – 24 °C);
d. If charging problems persist, take the tool, battery
pack and charger to your local service center.
4. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may
also charge a partially used pack whenever you desire
with no adverse effect on the battery pack.
5. Foreign materials of a conductive nature such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities. Always
unplug the charger from the power supply when there
is no battery pack in the cavity. Unplug the charger
before attempting to clean.
6. Do not freeze or immerse the charger in water or any
other liquid.
Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non-metallic brush. Do not use water or
any cleaning solutions.

Wall Mounting

DCB107, DCB112, DCB113, DCB115, DCB118, DCB132
These chargers are designed to be wall mountable or to
sit upright on a table or work surface. If wall mounting,
locate the charger within reach of an electrical outlet,
and away from a corner or other obstructions which may
impede air flow. Use the back of the charger as a template
for the location of the mounting screws on the wall. Mount
the charger securely using drywall screws (purchased
separately) at least 1" (25.4 mm) long, with a screw head
diameter of 0.28–0.35" (7–9 mm), screwed into wood to an
optimal depth leaving approximately 7/32" (5.5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in the slots.

Intended Use

Your heavy-duty cordless rotary hammer is designed for
professional concrete drilling and chiseling applications.
DO nOT use under wet conditions or in presence of
flammable liquids or gases.
Your heavy-duty cordless rotary hammer is a professional
power tool.
8
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
sPECiFiCATiOns
Rated Size
Tool Holder
Voltage (DC)
Impact Energy in Joules (EPTA)
No-Load RPM
No-Load BPM
Optimum Drilling Range
Max. Diameter Core
Rotation Control
Weight
Length
Width
Height
Vibration Control
Chipping
Variable Speed Dial
Variable Speed Dial Positions
Dust Extraction Model #
Noise Values [dB(A)]
L (Emission Sound Pressure Level)
pA
L (Sound Power Level)
WA
K (Uncertainty of Given Sound Level)
Vibration Values (m/s 2 )
Drilling into Concrete (Value a
h,HD
Uncertainty K
Chipping/Chiselling (Value a
h,Cheq
Uncertainty K

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Side Handle (Fig. B)

WARNING: To reduce the risk of personal injury,
ALWAYS operate the tool with the side handle
properly installed. Failure to do so may result in
the side handle slipping during tool operation and
subsequent loss of control. Hold tool with both hands
to maximize control.
DCh614
1-3/4" (45 mm)
SDS MAX
60 V
10.5
190–380
1450–2900
5/8"–1-1/4" (16 mm–32 mm)
5" (125 mm)
®
E-Clutch
15 lbs. (6.8 kg)
20.7" (52.6 cm)
4.4" (11.2 cm)
9.9" (25.1 cm)
®
SHOCKS
Yes
Yes
7
DWH053 / DWH050
93
104
3
) 8.8
1.5
) 8.1
1.5