Idiomas disponibles
Idiomas disponibles
4. Intended use
The compressor is designed to generate compressed air for
compressed-air driven tools which can be driven with an air
volume of up to approx. 260 l/min (e.g. tire inflator, blow-
out pistol and paint spray gun). Due to the limited air output
it is not possible to use the compressor to drive tools with
very high air consumption (for example orbital sanders, die
grinders and hammer screwdrivers).
The equipment is to be used only for its prescribed purpose.
Any other use is deemed to be a case of misuse. The user
/ operator and not the manufacturer will be liable for any
damage or injuries of any kind caused as a result of this.
Please note that our equipment has not been designed for
use in commercial, trade or industrial applications. Our
warranty will be voided if the equipment is used in com-
mercial, trade or industrial businesses or for equivalent
purposes.
5. Safety information
m Attention! The following basic safety measures must be
observed when using electric tools for protection against
electric shock, and the risk of injury and fire. Read all these
notices before using the electric tool and keep the safety
instructions for later reference.
m Attention! The following basic safety actions must be
taken when using this compressor in order to protect the us-
er from electric shocks and the risk of injury and fi re. Read
and follow these instructions before using the equipment.
Safe work
Keep the work area orderly
1
Disorder in the work area can lead to accidents.
–
2
Take environmental influences into account
–
Do not expose electric tools to rain.
–
Do not use electric tools in a damp or wet environ-
ment. There is a risk of electric shock!
–
Make sure that the work area is well-illuminated.
Do not use electric tools where there is a risk of
–
fire or explosion.
3
Protect yourself from electric shock
–
Avoid physical contact with earthed parts (e.g.
pipes, radiators, electric ranges, cooling units).
4
Keep children away
–
Do not allow other persons to touch the equipment
or cable, keep them away from your work area.
Securely store unused electric tools
5
–
Unused electric tools should be stored in a dry,
elevated or closed location out of the reach of
children.
6
Do not overload your electric tool
They work better and more safely in the specified
–
output range.
7
Wear suitable clothing
–
Do not wear wide clothing or jewellery, which can
become entangled in moving parts.
18
GB/IE
–
Rubber gloves and non-slip shoes are recom-
mended when working outdoors.
Tie long hair back in a hair net.
–
Do not use the cable for purposes for which it is not
8
intended
–
Do not use the cable to pull the plug out of the
outlet. Protect the cable from heat, oil and sharp
edges.
9
Take care of your tools
Keep your compressor clean in order to work well
–
and safely.
–
Follow the maintenance instructions.
–
Check the connection cable of the electric tool
regularly and have it replaced by a recognised
specialist when damaged.
–
Check extension cables regularly and replace
them when damaged.
10
Pull the plug out of the outlet
–
During non-use of the electric tool or prior to
maintenance and when replacing tools such as
saw blades, bits, milling heads.
11
Avoid inadvertent starting
Make sure that the switch is switched off when
–
plugging the plug into an outlet.
12
Use extension cables for outdoors
–
Only use approved and appropriately identified
extension cables for use outdoors.
–
Only use cable reels in the unrolled state.
13
Remain attentive
Pay attention to what you are doing. Remain
–
sensible when working. Do not use the electric tool
when you are distracted.
14
Check the electric tool for potential damage
–
Protective devices and other parts must be care-
fully inspected to ensure that they are fault-free
and function as intended prior to continued use of
the electric tool.
–
Check whether the moving parts function fault-
lessly and do not jam or whether parts are dam-
aged. All parts must be correctly mounted and
all conditions must be fulfilled to ensure fault-free
operation of the electric tool.
Damaged protective devices and parts must be
–
properly repaired or replaced by a recognised
workshop, insofar as nothing different is specified
in the operating manual.
–
Damaged switches must be replaced at a cus-
tomer service workshop.
–
Do not use any faulty or damaged connection
cables.
Do not use any electric tool on which the switch
–
cannot be switched on and off.
15
Have your electric tool repaired by a qualified
electrician
–
This electric tool conforms to the applicable safety
regulations. Repairs may only be performed by an
electrician using original spare parts. Otherwise
accidents can occur.
