T1000
T1000 Qualified Tool Operator examination
OPERATOR'S NAME
HOME ADDRESS
COMPANY NAME
COMPANY ADDRESS
SIGNATURE
☐ Check the correct answer
3
1 It is necessary to read the Operator's Manual prior to operating a D
☐ True ☐ False
2 When fastening into concrete, the base material should be greater than the shank penetration by
at least: ☐ 1 time ☐ 2 times ☐ 3 times
3 When operating a powder actuated tool, your hand should never be placed:
☐ around the tool body ☐ in front of the tool muzzle ☐ over the tool handle
4 To determine the suitability of a base material, use the fastener as a center punch.
• If the fastener is blunted, do not fasten; the material is too:
☐ soft ☐ hard ☐brittle
• If the fastener penetrates easily, do not fasten; the material is too:
☐ soft ☐ hard ☐ brittle
• If the material cracks or shatters, do not fasten; the material is too:
☐ soft ☐ hard ☐ brittle
5 Unsafe applications for powder actuated tools may be caused by which of the following?
☐a soft base material ☐improper powder load ☐fastening too close to an unsupported edge
☐a malfunctioning tool ☐fastening into a spalled area ☐fastening through a pre-existing hole ☐all of the above
6 Which one of the following building materials is not suitable as a receiving material (base material) for powder actuated fasteners? ☐ sheet rock ☐ wood ☐ fiberglass ☐ sheet metal
☐ all of the above
7 When considering the safety of a particular application, the operator must think about:
☐ the base material ☐ the powder load power level ☐ the operator's safety
☐ the safety of bystanders and fellow workers ☐ all of the above
8 The proper loading procedure is: insert fastener first, powder load second. The fastener should always be placed in the tool prior to the load. ☐True ☐ False
9 Which one of the following materials is usually suitable for powder actuated fastenings?
☐ poured concrete ☐ hollow tile ☐ surface hardened steel ☐glazed brick
10 In concrete, a fastener should be driven no closer to an unsupported edge than:
☐ 1/2" ☐1-1/2" ☐ 3"
11 Fishhooking is a condition which can occur when a powder actuated fastener strikes a piece of hard aggregate or very hard concrete, bends and comes out of the work surface. A fishhook can cause a
serious injury or death. ☐True ☐ False
12 Placing a hand over the muzzle bushing of a loaded tool can result in serious injury from piston overdrive or an escaping fastener if the tool is discharged accidentally. ☐ True ☐ False
13 Piston overdrive is caused by overpowering of the tool or by discharging the tool against
a soft surface. ☐ True ☐False
14 Malfunctioning tools cannot be used and must be removed from service immediately.
15 After conducting a Center Punch Test,the best way to check the base material is to set several fasteners using the least powerful load. ☐ True ☐False
16 Eye protection and hearing protection should not be worn by the operator and any necessary bystanders when using the tool. ☐ True ☐False
17 A powder actuated tool cannot be safely used in an explosive or flammable atmosphere.
☐ True ☐False
18 List the proper powder load level number (1-6) next to each color listed.
Red___ Brown ___ Green ___ Yellow ___ Gray ___ Purple ___
19 The weakest power level should be used when making the first fastening.
20 You can fasten into welded areas of steel. ☐ True ☐False
T1000
• The proper procedure if a powder load fails to ignite is to hold the tool against the work surface and wait 30 seconds, then proceed exactly as directed in the Operator's Manual. ☐ True ☐False
WALT powder loads for the T1000 are .22, "A" tapered, neck down, rim fire short crimped cartridges. No other powder load may be used in this tool. ☐ True ☐False
• D
E
• Operators should never compress the T1000 or any other powder actuated tool against any part of their body. ☐ True ☐False
• If a piston buffer for the T1000 becomes deformed, simply remove it, and use the tool without the buffer? ☐ True ☐False
LICENSE AND WARRANTY ACTIVATION
The T1000 Tool is warranted for 3 Years from date of purchase on manufacturers defects.
I certify that I have read and understand the T1000 Tool Operating Instruction Manual and have taken the
Operator's exam. I understand the importance of following all safety procedures and that failure to read, comprehend, and follow the detailed rules and warnings regarding the safe operation of powder actuated tools can result in
serious injury or death to the tool operator or bystanders. I agree to conform to all the rules and regulations regarding the use of powder actuated tools.
(Please print clearly)
THE SERIAL NUMBER ON MY TOOL IS:
PLEASE SEND MY TOOL LICENSE TO:
NAME
HOME ADDRESS
CITY
MAIL TO:
Tool License Coordinator • D
WALT, Inc.• 2 Powers Lane, Brewster, NY 10509
E
(please print clearly)
AGE
WALT low velocity tool.
E
☐ True ☐ False
STATE
DATE OF BIRTH
PHONE
COMPANY PHONE
DATE
ZIP
PHONE
DDF211001P 6