Idiomas disponibles
Idiomas disponibles
Warning - Batteries
• When inserting batteries, note the correct polarity (+ and -
markings) and insert the batteries accordingly. Failure to do so
could result in the batteries leaking or exploding.
• Only use batteries that match the speci ed type. Keep the
instructions for the correct choice of batteries included with the
operating instructions of devices safe for future reference.
• Before you insert the batteries, clean the battery contacts and the
polarity contacts.
• Do not allow children to change batteries without supervision.
• Replace all the batteries in a set at the same time.
• Do not mix old and new batteries, or batteries of different types or
from different manufacturers.
• Remove the batteries from products that are not being used for
an extended period (unless these are being kept ready for an
emergency).
• Do not short-circuit batteries.
• Do not charge batteries.
• Do not burn batteries or heat them up.
• Never open, damage or swallow batteries or allow them to enter
the environment. They can contain toxic, environmentally harmful
heavy metals.
• Remove spent batteries from the product and dispose of them
without delay.
• Avoid storing, charging and using in extreme temperatures and
at extremely low atmospheric pressures (such as at
high altitudes).
• Ensure that batteries with damaged housings do not
come into contact with water.
• Keep batteries out of the reach of children.
4. First steps - Inserting the batteries
Note
• Use 2 type AAA batteries.
• Remove the battery cover on the underside of the remote control.
• Ensure the correct polarity (+/-) of the batteries and the battery
compartment.
• Insert the batteries.
• Reattach the battery cover on the remote control.
Note - code memory
This remote control saves the settings even during a battery change.
Note: Energy saving function
The remote control switches itself off automatically if a button is
pressed for longer than 15 seconds. This prolongs the life of the
batteries if the remote control is stuck in a place where the buttons
are pressed permanently, e.g. between sofa cushions.
Note:
Low battery display
• This remote control indicates when the batteries are getting low.
• If the status LED ashes 2 times after a button is pressed, the
batteries are weak and should be replaced promptly.
5. Setup
With the factory settings supplied, the remote control can control
approx. 90% of all PANASONIC devices. There is no need to make any
settings. If the remote control does not work, select one of the setting
options mentioned in 5.1 and 5.2 below.
5.1 Code input
CODE list:
001, 002, 003, 004, 005, 006, 007, 008, 009, 010, 011, 012, 013,
014, 015, 016, 017, 018, 019, 020, 021, 022, 023, 024, 025, 026,
027, 028, 029, 030, 031, 032, 033, 034, 035, 036, 037, 038, 039,
040, 041, 042, 043, 044, 045, 046, 047, 048, 049, 050, 051, 052
1. Press and hold the [MUTE] and [POWER] buttons simultaneously for
approx. 3 sec. until the status LED lights up continuously.
2. Enter a 3-digit code from the code list using the number keys. The
status LED confirms each number entered with a short flash. When
all three digits have been entered, the status LED goes out. If you
have entered an invalid device code, the status LED flashes 3 times
and then lights up permanently again for a new code entry.
3. Test the functions of the remote control. If the function does not
work properly, try other device codes: [002], [003], [004], etc.
Note
If you have entered an invalid device code, the status LED ashes
twice and then shows a steady light again. To exit the device code
entry, press the mute button [MUTE].
5.2 Code search
1. Press and hold [MUTE] and [POWER] simultaneously for approx. 3
sec. until the status LED lights up.
2. Press the [CH+ or CH-] button to start the code search. With each
button press, the remote control sends a new code to your TV. If
your TV switches to a different programme, also test the found
device code using the [POWER], [VOL+], [VOL-], [MENU] buttons
and the number keys 0-9. If the functions work, press the [MUTE]
button to save the device code and end the search.
3. If the functions do not work, repeat the search by pressing the
[CH+] button.
2
