Idiomas disponibles
Idiomas disponibles
32 |
Ignition of bain-marie (Fig. 8)
Check that the water outlet tap (B) is closed. Fill the tank
with water up to the marked level. Activate the main switch
upstream from the appliance. Using the knob (A), position
the power regulator to the largest part of the serigraphy
to increase the power levels. To decrease the power, rotate
the knob to the smallest part of the serigraphy.
To switch the appliance off, rotate the knob (A) to position
0 and switch off the main switch.
Pasta cooker safety device (Fig. 7)
The appliance is equipped with a safety thermostat that
intervenes in the event of an anomalous operation of the
pasta cooker (for example, the pasta cooker is ignited
without having filled the tank with water). To restart the
appliance, disconnect the power supply by means of the
disconnecting switch placed before the appliance, let
the unit cool down and press the Reset button (E). Later,
to restart the appliance, follow the instructions in the
paragraph OPERATION.
EN
Draining the tank
For the Top version, the operator has to use a proper
container to drain the tank. Connect a draining pipe with
a bayonet connection as shown in Fig. 6. Open the drain
tap (B) (Fig. 7-8). For the version with cabinet, the drain tap
is connected to the network and, therefore, it is sufficient
to open the drain tap (B) placed inside the compartment
(Fig. 9).
RECOMMENDATIONS AND PRECAUTIONS
FOR THE USE OF THE PASTA COOKER BASKETS
The pasta cooker's baskets are made of austenitic stainless
steel; this material is the most suitable for the construction
of the baskets but, in some conditions, it may be affected
by corrosion caused by chloride ions (sodium chloride=
cooking salt) that are normally present in water where the
baskets are immersed.
Therefore, it is essential to follow a few easy precautions to
avoid this problem.
1) Never let the baskets dry without having rinsed them
first with lukewarm water.
2) After each use, properly rinse the baskets with lukewarm
water or suitable products.
3) Never pour salt directly inside the baskets.
4) Do not use abrasive products or accessories.
Warning: while washing the baskets, pay attention to
the areas where there are some gaps (i.e. welding, area
attaching to the supporting structure, etc. ) because,
in these areas, salt water can stagnate and later cause
corrosion.
To clean the steel parts, refer to the paragraph "CARE OF
THE APPLIANCE".
Important!
MOD.
N°:
Qn
V
kW:
Hz: 50/60
For the TOP versions, maintain the distance between
the appliance and the edge of the top (see fig. 6).
MAINTENANCE
CARE OF THE APPLIANCE
ATTENTION!
- Before cleaning, switch off the unit and let it cool
down.
- In the event of electrically supplied units, use the
isolator switch to disconnect the mains. Carefully clean
daily the appliance to guarantee its proper operation
and long life. Steel surfaces must be cleaned with a dish
washer detergent diluted in very hot water by using
a soft cloth; for the toughest dirt, use ethylic alcohol,
acetone or another non-halogenated solvent; do not
use abrasive powder detergents or corrosive substances
such as hydrochloric acid, muriatic or sulphuric acid.
The use of acids can affect the unit's operation and safety.
Do not use brushes, steel cottons or abrasive disks
made with other metals or alloys that might cause
rust stains due to contamination. For the same
reason, avoid contact with iron objects. Do not use
steel cottons or stainless steel brushes because whilst
they will not contaminate surfaces, they can cause
damaging scratches.
Metal powder, metal shavings from working and iron
material in general, when in contact with stainless steel
surfaces, can cause rust stains. Superficial rust stain might
be present on new appliances and they can be removed
with a detergent diluted in water and a Scotch Brite
sponge. If dirt is tough, do not use sandpaper or rough
paper, but use synthetic sponges (for example Scotchbrite
sponges). Do not use substances for cleaning silver and
be careful with hydrochloric or sulphuric vapours coming
from floor washing products, for example. Do not aim
water jets directly on the appliance, it might be damaged.
After cleaning, rinse properly with clean water and dry
carefully with a cloth.
REPLACEMENT OF THE COMPONENTS
(SPARE PARTS)
Use only original spare parts supplied by the
manufacturer.
All maintenance must be carried out by qualified
personnel. The appliance should be serviced at least
once a year, which is why we recommend subscribing our
maintenance agreement.
LONG PERIODS OF APPLIANCE INACTIVITY
If the appliance is not used for long periods of time, please
observe the following:
1) Switch off the disconnecting switch to disconnect the
mains
2) Clean the equipment and the surrounding areas
properly
IPX
