Idiomas disponibles
Idiomas disponibles
In the E9BM4M, E9BM8M, SE9BM4M, SE9BM8M models,
the terminal board is found in the line box positioned
on the bottom of the appliance. Open the doors (B), if
present, to reach the box.
3) Connect the disconnecting switch (A) to the terminal
board (H) as shown in the figure and in the electrical
diagrams at the end of this manual. The chosen
connection cable must have features similar to the
H07RN-F type with an operating temperature of at least
80°C and have a section suitable to the unit (see the
Technical Data table).
4) Pass the cable through the passage and tighten the cable
stopper, connect the conductors in their corresponding
position to the terminal board and attach them. The
yellow-green ground conductor must be longer than
the others so that, in the event that the cable stopper
breaks, it disconnects itself after the voltage cables.
Equipotential
The appliance must be connected to an equipotential
system. The connection screw of the Top appliances is
positioned on the right back side while, in the other units,
the screw is always on the right bottom.
The screw is marked by the symbol:
Connection to the water network
The appliance must be connected permanently to the
water network; never use a flexible pipe connection set.
If possible, connect the water inlet pipe to the water
MOD.
N°:
network by a mechanical filter and a shut-off tap. Before
Qn
V
kW:
Hz: 50/60
IPX
connecting the filter, allow the water to flow for a short
time to eliminate any possible ferrous residuals from the
duct.
Water discharge
Connect the overflow discharge pipe to the sewage
network.
Attention!
The manufacturer is not responsible and will not
reimburse, under the guarantee, damages due to the
improper installation and installation that does not
conform to these instructions.
APPLIANCE TEST
Important
Before putting it in operation, test the equipment to
evaluate the operational conditions of each component
and single out any possible anomalies.
During this phase, it is important that safety and
hygiene conditions are strictly followed.
Carry out the following controls to perform the test:
1) Check that the main voltage is in conformity with the
appliance voltage
2) Use the automatic disconnecting switch to check the
electrical connection
3) Check the proper operation of safety devices
After testing, if necessary, train the users so that they
understand all necessary skills to operate the equipment
in safe conditions, according to the regulations in force in
the country in which the equipment is to be used.
USE INSTRUCTIONS
ATTENTION!
This appliance cannot be used by people (including
children) with impaired skills or without experience
and knowledge unless under the supervision of a
person responsible for their safety who provides
precise instructions about the use of the unit.
Keep children under supervision to make sure that
they don't play with the unit.
Use the appliances under supervision and never
operate while empty. The maximum resistance
pressure of the pasta cookers and bain-marie is 700
kpascal.
Pilot lights indicate if every unit is on or off.
The appliance does not need particular adjustment
interventions by specialized people except for the
regulations made during the user's operation.
Use only the accessories recommended by the
manufacturer. During the initial uses of the appliance,
an acrid or burning smell may be detected. This will
disappear after two or three uses.
After use, the areas are hot for a certain amount of time
(residual heat). Avoid resting your hands on them and
allowing children to get too close!
These are very important regulations; if they are
neglected, the appliance may not perform properly or
the user may be placed at risk.
OPERATION
Before using the unit for the first time, clean the tank
properly (see the paragraph "Care of the appliance"). Check
the appliance connection and put it into service following
the instructions.
Switching on the pasta cooker (Fig. 7)
Check that the water faucet (B) is closed. Fill the tank with
water up to the overflow hole by rotating the handle (F).
For the 900 series models, this hole is located on the upper
side under the removable grill. In the 700 series models,
this hole is located on the vertical side of the tank.
Activate the main switch upstream the appliance.
With the handle (A), position the thermostat on the desired
temperature between 30 °C and 90 °C. The pilot light (C)
switches on, which means that the heating elements are
activated. As soon as the desired temperature is reached,
the pilot light switches off. To switch the unit off, rotate the
handle (A) to "0" and switch off the main switch.
| 31
EN
