Sammic CK-241 Instrucciones página 14

EN
MAINTENANCE
- Verify before each use that the machine's safety devices are working proper-
ly. Call the SAMMIC authorised technical service if you detect any anomaly.
- Check the condition of the drive shaft seal on a weekly basis to ensure that
this area remains water-tight. Installing a new seal is recommended every
time the drive shaft is loosened for maintenance.
- If the power cable is damaged, a new one must be installed before the
machine is used again. Only a SAMMIC authorised technical service may
perform this replacement.
- If the engine block (K) is damaged, the affected parts must be replaced
before the machine is used again. Only a SAMMIC authorised technical
service may perform this replacement.
- The noise level in operation (according to EN ISO 11201:1995) is less than
70 dB(A) with the machine placed at a height of 1.6 m and a distance of 1
m. Background noise: 32 dB(A)
FUNCTIONS AND OPERATION OF THE
ELECTRONIC CONTROL
MACHINE ENERGISED PILOT LIGHT (1):
When the cutter is connected to the main supply, pilot light (1) turns on to
indicate that the cutter is energised.
STATUS/SAFETY PILOT LIGHT (2):
Pilot light (2) provides information about the machine's status.
Cutter mode:
- When the light is off, the motor is stopped, the lid (E) closed and the plunger
(B) down.
- When the light is on, the motor is running, the lid (E) closed and the plunger
(B) down.
- When it flashes, the lid (E) is closed and the plunger (B) up.
- It also flashes when the lid (E) is open.
Cutter mode:
- When the light is off, the motor is stopped, the pot (O) and pot lid (M) are
closed.
- When the light is on, the motor is running, the pot (O) and pot lid (M) are
closed.
START BUTTON (3)
Cutter mode:
- When the lid (E) is closed and the plunger (B) down, pressing this button
will start the motor.
- When the motor is stopped, the lid (E) closed and the plunger (B) up, the
"safety" pilot light (2) will start flashing if the button is pressed. The motor
will start if the plunger (B) is lowered.
- The motor will stop if the plunger (B) is raised. When the plunger (B) is
lowered, the motor restarts automatically. The "Start" button (3) must be
pressed again to start the motor if the plunger (B) is kept in the raised posi-
tion for more than 30 seconds.
- The motor will stop if the lid (E) is opened. The motor will automatically
restart when the lid (E) is closed again. If the lid (E) is not closed within
30 seconds, the "Start" button (3) must be pressed again to restart the
motor.
- The machine will stop automatically after 30 minutes if it is left running with
the plunger (B) down.
Cutter mode:
- With the pot (O) in position and the pot lid (M) closed, pressing this button
will start the machine.
PULSE (4)
The motor starts and runs as long as this key is held down and stops when
it is released.
STOP 5
The machine will stop when this button is pressed.
START-UP AND GENERAL OPERATION
"Vegetable Cutter" (CK-241, CA-21) operating mode
The "Vegetable Cutter" accessory (F) can be positioned in two different
directions (FIG 3) so that the outlet for the products faces one direction or
the other.
With the machine disconnected from the mains:
- Place the "Vegetable Cutter" (F) accessory on the motor block and turn it
anticlockwise as shown in the diagrams (FIG 4).
- The lid (E) must be fitted as shown in the drawings by turning it anticloc-
kwise (FIG-5).
- Place the plunger (B) and secure it with the pin (C), as shown in the dia-
grams (FIG 6).
Fitting the disks (A) and screens (G) (FIG 2)
- Remove the lid (E) - plunger (B) assembly by turning it clockwise (FIG 4).
- Place the ejector (I) in its housing on the drive shaft or discharge ramp (H).
- Insert the screen (G) into the lower cover (F) cavity when required for the
process.
- Fit a disk (A) on the drive shaft. Disks that work with screens need to be
fastened in position.
- Replace the lid (E) - plunger (B) assembly by turning it anticlockwise.
Operation with the standard intake hopper (Q) and plunger (B). CK-241
y CA-21
- The mallet (D) must be housed and locked in its hole. Rotate it anti-cloc-
kwise to do so.
- Start the machine.
- Raise the plunger (B). The motor stops.
- Insert the products in the standard hopper (Q).
- The motor starts and the cutting process begins when the plunger starts to
lower (B). Push the product by gently lowering the plunger (B). Repeat the
process as many times as required.
- Press "Stop" (14) to finish.
Operation with cylindrical hopper (P). CK-241, CA-21.
This Ø 47 mm hopper is used to cut long, cylinder-shaped vegetables such
as carrots, endives, cucumber, etc.
- Start the machine.
- Release the mallet (D) by rotating it clockwise.
- Insert the products through the hole and push them gently with the "Mallet"
- 14 -