Parkside PDS 120 B2 Instrucciones De Utilización Y De Seguridad página 36

14. Take care of your tools
- Keep cutting tools sharp and clean in order to be able
to work better and more safely.
- Follow the instructions for lubrication and for tool
replacement.
- Check the connection cable of the power tool regularly
and have it replaced by a recognised specialist when
damaged.
- Check extension cables regularly and replace them
when damaged.
- Keep the handle dry, clean and free of oil and grease.
15. Pull the connector out of the socket
- When the power tool is not in use or prior to
maintenance and when replacing tools such as saw
blades, bits, milling heads.
16. Do not leave a tool key inserted
- Before switching on, make sure that keys and adjusting
tools are removed.
17. Avoid inadvertent starting
- Make sure that the switch is switched off when
plugging the plug into an outlet.
18. Use extension cables for outdoors
- Only use approved and appropriately identified
extension cables for use outdoors.
19. Remain attentive
- Pay attention to what you are doing. Remain sensible
when working. Do not use the power tool when you
are distracted.
20. Check the power tool for potential damage
- Protective devices or other parts with minor damage
must be carefully inspected to ensure that they function
correctly and as intended prior to continued use of the
power tool.
- Check whether the moving parts function faultlessly
and do not jam or whether parts are damaged. All
parts must be correctly mounted and all conditions
must be fulfilled to ensure fault-free operation of the
power tool.
- Damaged protective devices and parts must be
properly repaired or replaced by a recognised
specialist workshop, insofar as nothing different is
specified in the user manual.
- Damaged switches must be replaced at a customer
service workshop.
- Do not use any power tool on which the switch cannot
be switched on and off.
21. ATTENTION
- The use of other insertion tools and other accessories
can entail a risk of injury.
22. Have your power tool repaired by a qualified
electrician
- This power tool conforms to the applicable safety
regulations. Repairs may only be performed by an
electrician using original spare parts. Otherwise
accidents can occur.
WARNING
This power tool generates an electromagnetic field during
operation. This field can impair active or passive medical
implants under certain conditions. In order to prevent the risk
of serious or deadly injuries, we recommend that persons
with medical implants consult with their physician and the
manufacturer of the medical implant prior to operating the
power tool.
6.2 Special safety instructions
• In an emergency, switch the machine off directly and pull out
the mains plug.
• Observe all of these notes before and while working with
the saw.
• Never use the saw to cut firewood.
• The machine is equipped with a safety switch against
reactivation if the voltage drops.
• If an extension cable is required, make sure that its cross-
section is sufficient for the current consumption of the saw.
Minimum cross-section 1.5 mm
• Only use cable reels in the unrolled state.
• Personnel working on the machine must not be distracted.
• Under no circumstances should the saw blades be braked by
pushing against the side after switching off the drive.
• Only install saw blades that are well sharpened, free of
cracks and not deformed.
• Faulty saw blades must be replaced immediately.
• Do not use saw blades that do not correspond to the
characteristics specified in these usage instructions.
• Ensure that all devices that cover the saw blade work
properly.
• Safety equipment on the machine must not be disassembled
or made unusable.
• Damaged or faulty protective devices must be replaced
immediately.
• Do not cut workpieces that are too small in order to keep
them secure in your hands.
• Do not load the machine so much that it comes to a standstill.
• Always press the workpiece firmly against the working plate.
• Never remove loose splinters, chips or jammed wood pieces
from the running saw blade.
• Switch off the machine to rectify any faults on the blocked
tool attachment. Pull out the mains plug. Remove the
blockage. Attention! Risk of injury due to saw blade! Wear
protective gloves! Perform a test run without a workpiece.
Make sure that no unusual noises or vibrations occur. If this is
the case, switch the device off and contact the manufacturer.
• Only carry out modifications, adjustments, measurements and
cleaning work when the motor is switched off. Pull out the mains
plug.
• Before switching on, make sure that keys and adjusting tools
are removed.
• Switch off the motor and pull out the mains plug when
leaving the work station.
• Electrical installation, repairs and maintenance work may
only be carried out by specialists.
• All protective and safety equipment must be reassembled
immediately after repair or when maintenance is completed.
.
2
GB/MT 31