GreenWorks 2505007 Manual De Utilización página 5

EN
DE ES IT FR PT NL RU FI SV NO DA PL CS SK SV HR HU RO BG EL AR TR HE LT LV ET
Before inspecting, cleaning, or servicing the ma-
chine, disconnect the plug from power source and
wait for all moving parts to stop. Failure to follow
these instructions can result in serious personal in-
jury or property damage.
Wear adequate clothing, gloves and goggles before
carrying out any maintenance.
REPLACING THE TINES (
In order to avoid serious personal injury, turn the
it off and unplug it before performing any mainte-
nance.
Use only the manufacturer's original replacement parts.
„ Disconnect dethatcher from the power source.
Allow sufficient time for moving parts to totally stop.
„ Turn the dethatcher over.
„ Remove the two star-shaped screws (11), the
flat washer (13) and the lock washer (14) which
secure the tine casing. Remove the two nuts on the
opposite side with a star-head screwdriver.
„ Press the lock (15) on the edge of the shaft with a
slotted screwdriver to separate the tine casing from
the shaft.
„ Replace the worn or broken tines with new ones.
„ Fasten the tine casing back together using the flat
washer and the lock washer in their original order.
All the screws to mount the halves of the tine holder
must have flat washer (13) and lock washer (14 )
on their threads to prevent screws from loosening
during usage.
REPLACING THE TINES
„ Remove the tine cartridge as demonstrated on
figure 5.
„ Secure tine cartridge on a workbench.
„ Push out the pin using a screwdriver (Not Sup-
plied). This may require the use of a rubber mallet
if more strength is required.
„ Remove and discard the worn/broken tines.
English (Original instructions)
WARNING
WARNING
)
See figure 5
WARNING
WARNING
(See figure 6)
„ Replace the tine into position and slide the pin
back into place pressing the pin against a solid
surface to pressure it back into place.
DANGER! THE DETHATCHER CYLINDER
CAN CAUSE INJURIES.
Prior to maintenance, unplug from the power source
and wait until the dethatcher cylinder has stopped.
Wear heavy-duty gloves for performing maintenance.
The lawn dethatcher should be cleaned after each use.
WHEN SERVICING, USE ONLY IDENTICAL RE-
PLACEMENT PARTS. USE OF ANY OTHER PARTS
MAY CREATE A HAZARD OR CAUSE PRODUCT
DAMAGE.
TO AVOID SERIOUS PERSONAL INJURY, WEAR
GOGGLES OR SAFETY GLASSES AT ALL TIMES
WHEN OPERATING THIS UNIT. WEAR A FACE
MASK OR DUST MASK IN DUSTY LOCATIONS.
BEFORE INSPECTING, CLEANING, OR SERVIC-
ING THE MACHINE, DISCONNECT THE PLUG
FROM POWER SOURCE AND WAIT FOR ALL
MOVING PARTS TO STOP. FAILURE TO FOLLOW
THESE INSTRUCTIONS CAN RESULT IN SERI-
OUS PERSONAL INJURY OR PROPERTY DAM-
AGE.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage fromvarious types
of commercial solvents and may be damaged by their
use. Use clean cloths to removedirt, dust, oil, grease,
etc.
DO NOT AT ANY TIME LET BRAKE FLUIDS, GASO-
LINE, PETROLEUM-BASED
ETRATING OILS, ETC., COME IN CONTACT WITH
PLASTIC PARTS. CHEMICALS CAN DAMAGE,
WEAKEN, OR DESTROY PLASTIC WHICH MAY
RESULT IN SERIOUS PERSONAL INJURY. ONLY
THE PARTS SHOWN ON THE PARTS LIST ARE IN-
TENDED TO BE REPAIRED OR REPLACED BY THE
CUSTOMER. ALL OTHER PARTS SHOULD BE RE-
PLACED AT ANAUTHORIZED SERVICE CENTER.
4
WARNING
WARNING
WARNING
WARNING
PRODUCTS, PEN-