Tabla de contenido
The brushes or the machine has stopped.
Activate the brushes and press the accelerator.
The flow adjustment lever is closed or almost
closed.
Adjust/increase the detergent solution outlet flow
as required.
The detergent solution filter is clogged.
Clean the filter.
The detergent feed conduit is clogged in some
point.
Clean out the conduit by removing the dirt.
The flow opening solenoid valve is burned.
Replace it.
8.2.5. NO SUCTION
The suction hose is not connected to the squeegee.
Connect it correctly.
The suction hose, the squeegee conduit or the
inspection compartment is clogged.
Clean out and remove any obstructions from the
conduits.
The suction motor is turned off.
Activate it.
The recovery tank is full.
Empty it.
The suction motor is not receiving electric power
or is burned.
Check the connections and, for the latter case,
replace the motor.
8.2.6. INSUFFICIENT SUCTION
The recovery tank cover was not correctly tightened.
Tighten it correctly.
The recovery tank drain hose plug is not perfectly
closed.
Close it correctly.
The suction hose, the squeegee conduit or the
inspection compartment is clogged.
Clean out and remove any obstructions from the
conduits.
8.2.7. THE BRUSH MOTOR OR THE SUCTION
MOTOR DOESN'T STOP
The relay switch is defective.
Stop the machine, cutting off the main power sup-
ply and disconnecting the main battery connector,
and contact the technical service centre.
8.2.8. THE SQUEEGEE DOESN'T CLEAN OR DRY
EFFICIENTLY
The squeegee blades are worn or are dragging
solid dirt.
Replace or clean them.
The squeegee adjustment is not correct; the
advancement must be exactly perpendicular to the
running direction.
Adjust the squeegee.
The suction hose, the squeegee conduit or the
inspection compartment is clogged.
Clean out and remove any obstructions from the
conduits.
8.2.9. THE BATTERY CHARGER DOESN'T WORK
The battery charge doesn't start.
Check that the battery charger is connected to the
battery. Consult the battery charger manual.
8.2.10. THE BATTERIES DO NOT CHARGE OR DO
NOT HOLD A CHARGE
At the end of the charging process, the battery is
not correctly charged (see the battery manufacturer's
instruction-maintenance manual)
Check the battery charger error message and
check the data indicated on the display (see the bat-
tery charger's instruction manual).
The batteries are new and do not generate 100%
of the rated performances.
The accumulator reaches the maximum perfor-
mance after 20-30 complete charge cycles.
The electrolyte has evaporated and does not
completely cover the plates.
Check the battery manufacturer's use and main-
tenance manual.
There are significant differences in density among
the various elements.
Replace the damaged battery.
Always consult the battery and battery charger use and
maintenance manual. If this does not solve the problem,
contact the authorised technical service centre.
The manufacturer CANNOT solve problems
caused by using batteries and battery chargers
that were not directly supplied.
9.
CONDITIONS OF WARRANTY
All our appliances are subjected to rigorous tests and
are covered by warranty against material or manu-
facturing defects for a period of 12 months. The war-
ranty comes into effect from the date of purchase.
The date of purchase is the date indicated on the
receipt issued by the Reseller when the appliance is
consigned. The manufacturer shall repair or replace
any faulty parts free of charge during the period cov-
ered by the warranty. Any defects, which cannot be
clearly attributed to material or manufacturing de-
fects shall be examined by one of our Technical Ser-
vice Centres or at our factory and charged in accord-
ance with the outcome. The following are anyhow
not covered by the warranty: accidental damage dur-
ing transportation or handling, accidental damage
caused by negligence or unsuitable conduct, dam-
age due to incorrect or improper uses or installations
which do not conform with the warnings included in
the instruction manual, and anyhow due to unusual
43
Tabla de contenido
