Hoffman Berkel PROXIMA B932 Manual Del Usuario página 10

SHARPENING DEVICE".
Usage of another sharpening
devices can cause serious in-
juries or damage the machine.
Never use another sharpening
device. The sharpening de-
vice is equipped with two fine
sharpening stones, one is for
sharpening and one is for tak-
ing off the burr.
Before sharpening:
1. make sure that the machine
is off;
2. position the thickness ad-
justment knob in the safety
position;
3. open the thickness gauge
plate completely;
4. position the carriage in the
centre;
5. lift up the product holder;
6. mount the sharpening device
in such a way to the thickness
plate that mount the sharpen-
ing device in such a way to the
thickness plate that the cone of
the sharpening device fits into
the slit on the bottom of the
thickness plate (direction of
arrow) (L);
7. pull out the pin on top of the
sharpening device in direction
of arrow and move the sharp-
ening device over the edge of
the thickness plate (M);
8. move the sharpening device
with the pulled out pin to the
front in direction of the blade
(direction of arrow), so that the
pin is engaged in the hole of the
thickness plate (N);
9. the sharpening stones are
now in the correct position,
the blade edge is positioned
between the two sharpening
stones;
10. switch on the machine;
11. turn the yellow handwheel
of the sharpening device in di-
rection 1 for about 15 seconds
(Fig. P);
12. switch off the machine;
13. for taking the burr off, turn
the yellow handwheel in direc-
tion 2 for about 2 seconds;
14. turn the yellow handwheel
to 0;
Remove the sharpening device
1. switch off the machine;
2. pull the pin of the sharpening
device upright;
3. tilt the sharpening device
aside to the right;
4. remove the sharpening device;
5. make a complete wet cleaning.
WARNING! The sharp-
!
ening wheel can easily be
removed from the sharpening
unit, removing it in the direc-
tion of the arrow. Keep the
wheel clean for correct sharp-
ening. Remove dirt and grease
with alcohol and a semi-rigid
nylon brush.
Lubrication
After a regular period of use, it
may be necessary to lubricate
the carriage guides. We recom-
mend executing this operation
every 1 month.
For lubrication, only use acid
free oil (we recommend Vase-
line oil). Do not use vegetable
oil.
For lubricating, oil the guiding
axle of the carriage.
SERVICE
No user-serviceable parts are
inside. Refer servicing to qual-
ified personnel. All the repair
and replacement operations
(like blade replacement, re-
placement of the motor belt,
replacement of the sub-basap-
late electrical system compo-
nents, repair of structural parts,
repair and/or re-placement of
sub-baseplate components, or
8
similar) shall be executed exclu-
sively by personnel authorized
by the manufacturer.
In the event service is need-
ed, you may return your food
slicer to the manufacturer or
to one of the Authorized Ser-
vice Centers. For information
about service centers please
contact us at:
[email protected].
! WARNING! The blade re-
placement is mandatory
if distance between the edge of
the blade and the internal edge
of the guard exceeds 6 mm.
WARRANTY
AND RESPONSIBILITY
The manufacturer
machines with a limited war-
ranty of 24 months from the
purchasing date. The warran-
ty is extended only to defects
that arise under intended use
conditions and proper use.
The warranty does not cover
defects resulting from faults
caused by transport, purchas-
er's incompetence or negli-
gence, improper installation
or earthing, unauthorised in-
terventions, natural wear and
tear, voltage variations greater
than 10% of the nominal value.
Moreover, the warranty does
not cover components intrin-
sically subject to wear, such as
blades and grinders, except in
the event of evident manufac-
turing defects.
The manufacturer declines any
direct and indirect responsibil-
ity coming from:
- failure to observe the instruc-
tions in this manual;
- use which does not conform
to prevailing specific regula-
tions in the country of instal-
lation;
supplies