Makita DLS713 Manual De Instrucciones página 18

Sierra de inglete telescópica inalámbrica
Ocultar thumbs Ver también para DLS713:
Tabla de contenido
Idiomas disponibles

Idiomas disponibles

1
(2)
(1)
(2)
(1)
► 1 . Inside corner 2. Outside corner
Measuring
Measure the wall length and adjust workpiece on table
to cut wall contact edge to desired length. Always make
sure that cut workpiece length at the back of the work-
piece is the same as wall length. Adjust cut length for
angle of cut. Always use several pieces for test cuts to
check the saw angles.
When cutting crown and cove moldings, set the bevel
angle and miter angle as indicated in the table (A) and
position the moldings on the top surface of the saw
base as indicated in the table (B).
In the case of left bevel cut
Table (A)
Bevel angle
Molding
position in
52/38° type
Fig. A
(1)
For inside
corner
(2)
Left 33.9°
(3)
For outside
corner
(4)
Table (B)
Molding
Molding edge against
position in
guide fence
Fig. A
Ceiling contact edge should
(1)
be against guide fence.
For inside
corner
(2)
Wall contact edge should be
against guide fence.
For
(3)
outside
corner
Ceiling contact edge should
(4)
be against guide fence.
EXAMPLE In the case of cutting 52/38° type crown
molding for position (1) in Fig. A:
Tilt and secure bevel angle setting to 33.9°
LEFT.
Adjust and secure miter angle setting to 31.6°
RIGHT.
Lay crown molding with its broad back (hidden)
surface down on the turn base with its CEILING
CONTACT EDGE against the guide fence on
the saw.
The finished piece to be used will always be
on the LEFT side of the blade after the cut has
been made.
(1)
(2)
(1)
(2)
(4)
(3)
(1)
(2)
Miter angle
45° type
52/38° type
45° type
Right 31.6°
Right 35.3°
Left 30°
Left 31.6°
Left 35.3°
Right 31.6°
Right 35.3°
Finished piece
Finished piece
will be on the
Left side of
blade.
Finished piece
will be on the
Right side of
blade.
In the case of right bevel cut
Molding
position in
Fig. A
(1)
For inside
2
corner
(2)
(3)
For outside
corner
(4)
Molding
position in
Fig. A
(1)
For inside
corner
(2)
For
(3)
outside
corner
(4)
EXAMPLE In the case of cutting 52/38° type crown
molding for position (1) in Fig. A:
Tilt and secure bevel angle setting to 33.9°
RIGHT.
Adjust and secure miter angle setting to 31.6°
RIGHT.
Lay crown molding with its broad back (hidden)
surface down on the turn base with its WALL
CONTACT EDGE against the guide fence on
the saw.
The finished piece to be used will always be on
the RIGHT side of the blade after the cut has
been made.
18 ENGLISH
Table (A)
Bevel angle
Miter angle
52/38° type
45° type
52/38° type
Right 31.6°
Right 33.9° Right 30°
Left 31.6°
Right 31.6°
Table (B)
Molding edge against
guide fence
Wall contact edge should be
Finished piece
against guide fence.
will be on the
Right side of
blade.
Ceiling contact edge should
be against guide fence.
Finished piece
will be on the
Left side of
Wall contact edge should be
blade.
against guide fence.
45° type
Right 35.3°
Left 35.3°
Right 35.3°
Finished piece
Tabla de contenido
loading

Tabla de contenido