EINHELL KGST 210/1 Manual De Instrucciones página 16

Anleitung KGST 210/1
GB
Follow all these instructions before and while you
are working with the saw.
Keep these instructions in a safe place.
Avoid body contact with earthed components.
When equipment is not being used it should be
kept in a dry, closed place out of children's reach.
You will work better and more safely if you keep
your tools sharp and clean. Check the power
cable regularly and have it replaced by an
authorized specialist at the first sign of any
damage.
Check your extension cables regularly and
replace them if damaged.
When working outdoors, use only extension
cables that are approved for outdoor use and
which are marked accordingly.
Concentrate on what you are doing. Take a
sensible attitude to your work. Never use the tool
when you are tired.
Never use a tool with a switch that cannot be
turned on and off.
Caution! The use of plug-in tools and accessories
other than those intended may put you at risk of
injury.
The machine is equipped with a safety switch (4)
to prevent it being switched on again accidentally
after a power failure (in bench-type circular saw
mode).
Never use the saw to cross-cut round timber.
Check the power cable. Never use a faulty or
damaged power cable.
Do not use the cable to pull the plug out of the
socket-outlet. Protect the cable from heat, oil and
sharp edges.
We recommend that you wear non-slip shoes
when working outdoors.
Keep long hair in a hair net.
Avoid abnormal working postures.
An untidy work area may result in accidents.
Do not allow other persons, particularly children,
to touch the tool or the power cable. Keep them
away from your workplace.
The splitter is an important safety device. Not
only does it guide the workpiece, it also prevents
the kerf closing behind the blade so that there is
no kickback from the workpiece. Note the
thickness of the splitter. The splitter should never
be thinner than the saw blade body or thicker
than the width of its kerf.
The guard hood (17) has to be lowered over the
workpiece for each cut.
Be sure to use a push stick when slitting narrow
workpieces smaller than 120 mm in width or a
push block when slitting narrow workpieces
smaller than 30 mm in width.
16
19.09.2002 18:49 Uhr
IMPORTANT! Never use this saw to make
plunge cuts.
Always stand to the side of the saw blade when
working with the saw.
Make sure that off-cuts do not catch on the saw
blade crown or they may be catapulted into the
surrounding area.
If the sawing gap is worn, replace the table insert.
- Pull out the power plug! -
To prevent injury from flying sawdust and chips,
use the saw only with a suitable vacuum
extraction system or standard industrial vacuum
cleaner.
Always pull the plug out of the power socket
before adjusting or servicing the machine.
Give these safety regulations to all persons who
work on the machine.
Do not use this saw to cut fire wood.
Caution! Hands and fingers may be injured on
the rotating saw blade.
Before you use the machine for the first time,
check that the voltage marked on the rating plate
is the same as your mains voltage.
If you need to use an extension cable, make sure
its conductor cross-section is big enough for the
saw's power consumption. Minimum cross-
section: 1.0 mm
If you use a cable reel, the complete cable has to
be pulled off the reel.
Never carry the saw by its cable.
Do not leave the saw in the rain and never use it
in damp or wet conditions.
Provide good lighting.
Never saw near combustible liquids or gases.
Wear suitable work clothes! Loose garments or
jewellery may become caught up in the rotating
saw blade.
Operators have to be at least 18 years of age.
Trainees of at least 16 years of age are allowed
to use the machine only under supervision.
Keep children away from the machine when it is
connected to the power supply.
Check the power cable. Never use a faulty or
damaged power cable.
Keep your workplace clean of wood scrap and
any unnecessary objects.
Persons working on the machine should not be
distracted.
Note the direction of rotation of the motor and
saw blade.
After you have switched off the motor, never slow
down the saw blade by applying pressure to its
side.
Fit only blades which are well sharpened and
have no cracks or deformations.
Seite 16
2
.