Before Use - Hitachi NC 40G Instrucciones De Manejo

Observe Safety Regulations
CAUTION
If the gas leaks from the metering valve or the gas
cartridge after attached the metering valve, replace
with the new metering valve.
Do not attempt to reuse the metering valve.
Replace with the new metering valve.
2. Battery
You must charge the battery before use.
The charging method of battery is shown in page 11.
3. Check on safety
CAUTIONS
Unauthorized persons (including children) must be
kept away from the equipment.
Wear eye protector.
Check the retaining screws which fix the top cover,
etc. for tightness.
Check the tool for defective or rusty parts.
Check whether or not the push lever works correctly
without nails, fuel cell and battery. Also check whether
or not any dirt has adhered to the moving parts of the
push lever.
Recheck on operational safety.

BEFORE USE

1. Insert battery into the tool (See Fig. 4)
Do not operate the push lever or trigger while
installing the battery.
Make sure the battery indicator light is flashing GREEN
(See Fig. 5).
If the battery indicator light is flashing RED, the battery
doesn't have enough power and it needs to be
charged.
BATTERY INDICATOR LIGHT
– Flashing GREEN: Enough power remaining (The
– Flashing RED: Insufficient power remaining (The
light turns steady during operation).
– OFF: The battery is extremely empty. Charge the
battery.
Power saving mode
If the tool has not been used for about an one hour
with the battery still installed, Power saving mode
turns on to minimize unnecessary consumption of
battery power. Power saving mode is also activated
when the battery power is extremely low or there's
an abnormality in the machine so please pay attention
to the battery indicator light after deactivating Power
saving mode (by removing the battery and reinstall
it).
2. Insert fuel cell into the tool
(1) Pulling the latch and open the cell cover (See Fig. 6).
(2) Insert the fuel cell into the tool (See Fig. 7).
(3) Insert the stem of fuel cell into the hole of adaptor
(See Fig. 8).
(4) Close the cell cover.
3. Load nails
(1) Insert nail strip into rear of magazine (See Fig. 9).
(2) Slide the nail strip forward in the magazine (See Fig. 10).
(3) Pull the nail feeder (B) back to engage the feeder knob
to the nail strip (See Fig. 11).
NOTE
Use nail strip of more than 10 nails.
light turns steady during
operation).
The Nailer is now ready to operate.
Removing the nails:
1 Pull the feeder knob backward (See Fig. 12).
2 Return the feeder knob forward quietly while pushing
the nail feeder (B).
3 Push the nail stopper. (See Fig. 13)
4 Pull out nails from the back of the magazine (See Fig.
14).
CAUTION
To prevent unintentional operation, never touch the
trigger or place the top end of the push lever on a
work bench on floor. Also, never face the nail outlet
toward any part of a person.
HOW TO USE THE NAILER
CAUTION
Never use the top cover or housing of this device as a
hammer.
Take precautions to ensure the safety of persons in
the vicinity during operation.
Squeeze the trigger when drive a nail, otherwise the
piston can not return correctly.
Make sure the nailing depth when the temperature is
above 40°C or below 0°C.
Hold the Nailer at right angles to the workpiece,
otherwise nails may ricochet and cause injury.
1. Nailing procedures
This power tool is equipped with a FULL SEQUENTIAL
ACTUATION MECHANISM.
(1) Intermittent nailing
Hold the Nailer at right angles to the workpiece and
depress the nail outlet onto the desired point; then pull
the trigger to drive a nail in a single shot (See Fig. 15).
After nailing once, nailing will not be possible again
until the trigger is released and pressed again.
(2) Push lever
When depressing the nail outlet, be sure to fully lift
the push lever (See Fig. 15) to release the safety lock.
Thus, nails cannot be driven without releasing the
safety lock even though the trigger is pulled.
The machine employs a preventive mechanism for
unloaded operation.
The machine enters a state where the push lever
cannot be pushed up. This takes place when the
magazine is not loaded with nails or when the
remaining number of nails becomes less than 3.
CAUTION
Do not drive a nail on another nail.
Use caution not to throw the push lever tip onto
workpiece when the push lever cannot be pushed up.
NOTE
Under low temperature conditions, the tool
sometimes does not operate correctly. Always operate
the tool at the appropriate ambient temperature.
2. Clearing a jam
WARNING
Handle with care to avoid burning yourself, since the
nails and nose may become very hot.
If nails are jammed in firing head, remove it, and adjust
the nailing in the following order.
1 Remove the fuel cell and the battery from the
Nailer. (See Fig. 16)
English
12