GreenWorks Tools 1300607 Manual De Utilización página 22

EN
DE
FR DE ES IT PT
FR EN ES IT PT
ASSEMBLY (POLE SAW)
WARNING
Before assembly, remove the battery from the tool.
FITTING AND REMOVING THE BATTERY (FIG.B)
Å Ê Ê¾» ¸·ÊÊ»ÈÏ Â¿Ä» ¿Ê ËÆ Í¿Ê¾ ʾ» È»¹»ÆÊ·¹Â»
on the tool. Slide the battery into the receptacle and
push until the battery snaps into place.
To remove the battery, push the release button
while at the same time pulling the battery out of the
receptacle.
WARNING
To prevent accidental operation, ensure that the
battery is removed and that the chain sheath is in
placed on the saw chain before performing the
following operations. Failure to do this could result in
serious personal injury.
FITTING THE SAW HEAD (FIG. C)
The saw head can be fitted directly to the handle in
order to achieve standard reach.
Align the groove on the outside of the coupling end
of the handle (3) with the tongue on the inside of the
coupling end of the saw head (4). Push the saw head
(4) onto the handle (3).
Slide the collar upwards and rotate it counter-
clockwise until it is fully tightened.
EXTENDING THE SAW HEAD (FIG.D)
The maximum reach can be achieved by fitting the
extension tube (9) between the saw head (4) and the
handle (3).
Align the groove on the outside of the coupling end
of the handle (3) with the tongue on the inside of the
coupling end of the extension tube (9).
Push the extension tube (9) onto the handle (3).
Slide the collar upwards and rotate it counter-
clockwise until it is fully tightened.
Align the groove on the outside of the coupling end of
the extension tube (9) with the tongue on the inside of
the coupling end of the saw head (4).
Push the saw head (4) onto the extension tube (9).
Slide the collar upwards and rotate it counter-
clockwise until it is fully tightened.
WARNING
Periodically check the connections to ensure that
they are tightened securely.
NL SV DA NO FI HU CS RU RO PL
NL SV DA NO FI HU CS RU RO PL
English (original instructions)
REMOVING THE SAW HEAD (FIG. C&D)
If the extension tube (9) is fitted, the saw head must be
removed first.
CHAIN TENSION (FIG. G&T)
Chains stretch with use, check and tension often.Never
tension a warm chain before storing, as chains shrink
when cool; this can damage chain, bar and saw.
15
SL HR ET
SL HR ET
To remove the saw head (4), rest the handle (3) on
ʾ» ½ÈÅËĺ ÂÅÅÉ»Ä Ê¾» ¹ÅÂÂ·È ·Äº Ê·Á» Šʾ» É·Í
head.
Release chain tension by turning the tensioning
screw, located behind the chain bar, counter-
clockwise.
Unscrew the locking knob.
Remove the cover.
The bar and chain can now be removed by lifting it
away from the main body of the saw and releasing
the chain from the drive pulley.
The pole saw can now be cleaned with a brush and
or rag to remove sawdust and oil.
To replace the bar and chain, loop the chain over
the drive pulley and place the bar against the centre
alignment groove.
Ensure that the adjusting block is located in the
tensioning hole on the chain bar.
Until that the rubber block and chain bar are free
from oil, as this helps to keep tension on the chain.
Replace the side cover and locking knob, but do not
tighten.
Using a screwdriver on the tensioning screw, turn
clockwise.
Tighten until there is enough play that the chain can
be pulled away from the bar, but not so much that
the runners can be pulled out of the bar.
Once you have the correct tension, fully tighten the
locking knob.
LT LV SK BG
LT LV SK BG