DeWalt D27300 Manual Del Usuario página 26

E N G L I S H
These are:
- Risk of accidents caused by the uncovered parts of the rotating blade.
- Risk of injury when changing the blade.
- Risk of squeezing fingers when opening the guards.
- Health hazards caused by breathing dust developed when planing
wood, especially oak, beech and MDF.
Labels on tool
The following pictograms are shown on the tool:
Read the instruction manual before use
When using the machine in the thicknessing mode, be aware
of the direction of feed. Never use the machine without
shavings collector in position.
When using the machine in the planing mode, be aware of the
direction of feed. Never use the machine without shavings
collector in position.
Make sure that the cutting blades are properly adjusted.
Do not allow the blades to protrude from the cutterhead by
more than 1.1 mm
Package contents
The package contains:
1 Partly assembled thickness planer
1 Guard
1 Shavings collector
1 Box containing:
1 Fence
1 Push stick
1 Bag containing:
1 Allen key 2.5 mm
1 Allen key 4 mm
1 Allen key 5 mm
1 Allen key 6 mm
1 Spanner 13/10 mm
1 Adjustment gauge
1 Elevating handle
2 Clamp handles
4 Rubber feet
1 M8 coach bolt
4 M8 nuts
4 D8 toothed washers
1 D8 flat washer
1 Box containing:
4 Legs
2 Wheels
2 Wheel brackets
1 Bag containing:
2 Wheel axles
4 M8 coach bolts
2 M8 hex head bolts
4 M8 nuts
4 Wing nuts
4 D8 flat washers
6 D8 Belleville washers
1 Instruction manual
1 Exploded drawing
• Check for damage to the tool, parts or accessories which may have
occurred during transport.
• Take the time to thoroughly read and understand this manual prior to
operation.
26
Description (fig. A1 & A2)
Your D27300/D27300T thickness planer has been designed for
professional planing of wood.
Fig. A1
1 On/off switch
2 Elevating handle
3 Lower table
4 Shavings collector
5 Scale lower table
6 Push stick
7 Fence clamp handle
8 Fence
Fig. A2
9 Upper table
10 Planning depth adjustment knob
11 Scale upper table
12 Guard clamp handle
13 Guard
Electrical safety
The electric motor has been designed for one voltage only. Always check
that the power supply corresponds to the voltage on the rating plate.
Using an extension cable
If an extension cable is required, use an approved extension cable suitable
for the power input of this machine (see technical data). The minimum
conductor size is 1.5 mm
When using a cable reel, always unwind the cable completely.
Also refer to the table below.
Conductor size (mm2) Cable rating (Amperes)
1.50 15
2.50 20
4.00 25
Cable length (m)
7.515 25 30
Voltage Amperes Cable rating (Amperes)
230 0 - 2.0 6
2.1 - 3.4 6
3.5 - 5.0 6
5.1 - 7.0 10
7.1 - 12.0 15
12.1 - 20.0 20
Three-phase machines should be wired directly into the mains by a
suitably qualified electrician.
Voltage drops
Inrush currents cause short-time voltage drops. Under unfavourable power
supply conditions, other equipment may be affected.
If the system impedance of the power supply is lower than 0.25
disturbances are unlikely to occur.
Assembly
Prior to assembly always unplug the tool.
Unpacking the machine and its parts (fig. B1)
• Remove the loose packaging material from the box.
• Lift the machine out of the box.
• Remove the parts box from the interior of the machine.
• Remove any remaining packing material from the machine.
B&D_17
2 .
45 60
6 6 6 6 6
6 6 6 6 6
6 6 6 10 15
10 10 10 15 15
15 15 15 20 20
20 20 20 25 -
,