Extraordinary Maintenance - Fama GS Serie Manual De Instruccion

Feeding voltage lacking.
Sectioning devices set on "OFF".
Intervened fuses or not functioning
The machine
magneto thermals.
doesn't
function: the
Lacked running button functioning
Archimedean
screw or the
grater roll
Thermal intervention
don't rotate
overheating
Damaged micro switch
Control electronic card block

EXTRAORDINARY MAINTENANCE

For the intervention of extraordinary maintenance, consequent to breaks or revisions or mechanical and electric damages, it
is necessary an intervention request directly to the Authorized Assistance Center.
The instructions about the extraordinary maintenance don't appear in the present instruction manual for the use and so
must be explicitly requested to the manufacturer.
CLEANING
It is forbidden to clean by hand the organs and the elements in motion.
All cleaning interventions must be started only and exclusively, after having unloaded the machine with the
food product in working and having insulated from the electric feeding source and from external energy.
The machine, the electric equipment and the machine board components must not be ever washed utilizing
water, and not in any kind of jets form and quantity; so, without "secchio" nor "rubber" nor "towel".
Don't put ever directly the machine in the sink or under the tap.
The machine hygiene level classification and the associated equipment, for the foreseen use, is 2 (two): machine that, after
an hygiene risk evaluation, is in conformance with applicable international standards requirements, but requests a programmed
disassembly for the cleaning.
FREQUENCY PERSONNEL
At the end of every
shift work and
however before the
daily use
Check and restore the electric energy.
Turn the sectioning devices in the position "ON"
Change the intervened fuses, check the magneto thermal switches state.
Check the START button efficiency and eventually contact directly the Authorized
Assistance Center.
due to the Wait the complete cooling before the machine restarting
Contact directly the Authorized Assistance Center
Disconnect the machine from the net for some minutes.
Operator All the surface and the machine parts destined to come in contact with the food product or with
the food zones (hopper internal surface, machine neck and the grinding group, the pestle, the
pressure, the grater mouth and the grater roll) and the jets zones (machine external surface)
must be cleaned and disinfected with the under reported modalities. For the grinding group
disassembly activities see the previous descriptions.
 Scrape the surfaces from the possible food product residuals (for example with plastic
scrapers);
 Clean all the food zone surfaces and jets zone with a morbid dampened clothes (not
draining) with detergent diluted in hot water (also common soap for dishes is good).
Don't soak them. With a towel clean inside the grinding mouth. Use specific products for
steel, which must be liquids (not in cream or pastries however abrasive) and above all must
not contain chlorine. Against the fat substances the denatured alcohol.
 Rinse with cleaned hot water and successively dry all food zone surfaces and jets zone
with soft clothes that don't lose coats.
PERIODS OF LONG INACTIVITY
 During the machine long inactivity periods provide to pass vigorously on all steel surfaces
(especially if stainless) a clothes soaked of Vaseline oil so that to spread a protective veil.
THINGS DA NON FARE BEFORE OR DURING THE CLEANING:
 Enter towards the moving elements without to be previously checked of their stop;
 Enter towards the moving elements without have stopped it in safety stop (blockage in zero
position of the electric feeding sectioning devices)
PRODUCTS NOT TO USE:
 Compressed air with jets towards the zones with flour warehouses and in general towards
the machine;
 Vapor equipment;
 Detergent that contains CLORO (also if diluted) or its compounds as: the bleach, the
muriatic acid, products to clear the drain, products for the marble cleaning, in general
decalcifying, etc ... can attack the steel composition, staining and oxidizing it unavoidable.
The only above described products fumes can oxidize and in any case corrode the steel;
 Steel wool, brushes or abrasive discs produced with other metals or alloys (ex. Common
steel, aluminum, brass, etc...) or tools that have previously cleaned other metals or alloys,
that except to scratch the surface.
 Detergents in abrasive dust;
 Fuel, solvents or inflammable and/or corrosive fluids;
 Substances used to clean the silver.
ORIGINAL INSTRUCTIONS TRANSLATION
MODALITY
Pag. di
12 13