Nice Neoplus Instrucciones Y Advertencias Para El Instalador página 4

4) Programming
Each radio control unit is recognised by the receiver incorporated in
the NEOPLUS control unit by means of a unequivocal "code".
A "memorisation" phase must therefore be performed in order to
allow the control unit to recognise each single radio control unit.
In order to command the motor via the remote controls, it is neces-
sary to memorize the transmitter (Table "A1") and program the direc-
tion of movement (Table "A2")
When the memory contains no codes the first radio control unit can be entered following the procedure detailed in table A1.
If the control unit already contains codes, 2 short beeps will be heard when it is switched on. This means that the above procedure is not
valid and you will have to proceed as described in table A4 "Memorizing other transmitters".
Table "A1" Memorizing the first transmitter (fig. 11)
1. As soon as the control unit is powered, 2 long beeps will sound
2. Within 5 seconds press and hold down button (for approx. 3 seconds)
3. Release button
Until the direction of movement is programmed, every command received by the motor will be signalled by a short beep.
Table "A2" Programming the direction of movement (fig. 12)
1. Press and hold down button
(after about 5 seconds).
2. Press and hold down buttons
until you hear 2 short beeps, signalling that the programming procedure for the direction
of movement has begun.
3. Within 2 seconds, press button
button
The success of the direction programming procedure will be signalled by 3 beeps
Note: all the remote controls memorized in the motor will now command movement in the direction you have just programmed
After programming the direction of movement, make sure that button
or the drawing back of the awning, and that button
!
If the anemometer triggers, this will cause the motor to carry out a manoeuvre equivalent to the
If the direction you have just programmed is not correct, you must delete the programmed data as described in table "A3", and repeat the
sequence detailed in table "A2", using the opposite button at step no. 3.
Table "A3" Deleting the direction of movement (fig. 13)
1. Press and hold down button
(after about 5 seconds)
2. Press and hold down buttons
until you hear the first of 5 beeps, signalling that the programmed direction of movement
has been deleted.
Note: all the remote controls memorized in the motor will no longer command any movement; a new programming procedure must
therefore be carried out (table "A2")
When one or more transmitters have already been memorised, others may be enabled as follows:
Table "A4" Memorizing other transmitters (fig. 14)
1. Press and hold down button
(after about 5 seconds)
2. Press button
3. Press button
4. Finally, 3 beeps will indicate that the new transmitter has been memorised correctly.
Note: If the memory is full (14 codes), 6 beeps will indicate that the transmitter cannot be memorized.
4
when you hear the first of the 3 beeps confirming memorisation
on a pre-memorized transmitter until you hear a long beep
and
to program the UP direction anticlockwise, or press
to program the UP direction clockwise.
commands the closing of the shutter or the unfolding of the awning.
on a pre-memorized transmitter until you hear a beep
and
on the new transmitter until you hear a beep
of a previously enabled transmitter slowly 3 times (old)
on the new transmitter again.
!
WARNING: All the memorisation sequences are timed,
i.e. they must be completed within the programmed time
limits.
• For radio controls featuring multiple "units", choose the
unit to which the motor should be associated before
proceeding with the memorisation process.
• Programming via radio may be done on all the motors
within the range of the transmitter; therefore, only the
one involved in the operation should be switched on.
on the transmitter to be memorized
(for approx. 5 more seconds)
on the transmitter actually commands the opening of the shutter
(for approx. 5 more seconds)
Example
3s
Example
5s
5s
button.
Example
5s
5s
Example
NEW 5s
OLD X3
NEW