Mounting The Guard - EGO STX3800 Manual Del Operador

WARNING: Do not attempt to modify this product
or create accessories not recommended for use with
this Line trimmer. Any such alteration or modification
is misuse and could result in a hazardous condition
leading to possible serious personal injury.
WARNING: To prevent accidental starting that
could cause serious personal injury, always unplug the
battery connector from the socket when assembling
parts.
WARNING: When the tool is equipped with brush
cutter head, the safety barrier bar should be mounted.

MOUNTING THE GUARD

WARNING: Always wear gloves when mounting
or replacing the guard. Take care of the blade on the
guard and protect your hand from cutting.
WARNING: Never operate the tool without the
guard firmly in place. The guard must always be on
the tool to protect the user! When the guard is fixed,
never attempt to remove or adjust the guard, if a
replacement is needed, it should be performed by a
qualified service technician!
Loosen and remove the two screws from the guard
(Fig. B), align the guard mounting holes with the assembly
holes and then lock the guard onto the shaft base with the
two screws, together with two spring washers (Fig. C).
WARNING: Make sure the guard is fixed
according to Fig. B & C, any reverse fixing will cause
great danger!
MOUNTING AND ADJUSTING THE LOOP HANDLE
1. Stop the motor and unplug the battery connector
from the socket., if installed.
2. Loosen the wing nut to separate the adjustable loop
handle (Fig. D).
NOTICE:
Install the safety barrier bar assembly onto
the loop handle with the two screws when the tool is
equipped with brush cutter head.
Fig. D parts description see below:
D-1 Loop handle
D-2 Clamping block
D-3 Wing nut
D-4 Safety barrier bar (Only
for brush cutter head)
D-5 Locking pole
56 VOLT LITHIUM-ION CORDLESS LINE TRIMMER — STX3800
NOTICE:
There are two kinds of locking pole, the shorter
one is for trimmer head. The longer one is for brush
cutter head. Be carefully to choose the correct locking
pole when using the tool.
3. Push the loop handle onto the shaft at the front of
threshold ring. Never place it between the threshold
ring and rear handle area.(Fig. E).
NOTICE: Adjust the loop handle between the threshold
ring and the warning label when the tool is equipped
with brush cutter head (Fig. F).
4. Insert the clamping block into the handle slot
(Fig. G).
5. Mount the locking pole, and pre-tighten them with
the wing nut. Make sure that the loop handle is
upwards and points toward the top of the rear handle
(Fig. H).
6. Adjust the loop handle between the threshold ring
and the label until find the comfortable position when
using the trimmer. .
7. Lock the lever of the locking pole (Fig. I).
WARNING: Never operate the tool without the
loop handle firmly in place.
WARNING: Only fix the loop handle between the
threshold ring and the label.
REPLACE THE TRIMMER HEAD WITH THE 3-TEETH
BLADE
Know the trimmer head as Fig. J shown. Then
disassemble the trimmer head and mount the 3-teeth
blade on the brush cutter.
Fig. J parts description see below:
J-1 Inner Flange
J-2 Flange Cover
J-3 Upper Housing ASSY J-7 Spool Retainer
J-4 Nut
1. Press the release tabs on the spool retainer and
remove the spool retainer by pulling it straight out
(Fig. K1 & K2).
2. Rotate the upper housing assembly to align the slot
in the flange with the shaft-locking hole in the gear
case and insert a stabilizer into the hole (Fig. K3).
3. Rotate the socket wrench clockwise to remove the
nut and upper housing assembly (Fig. K4).
4. Remove the guard accessory by loosening the three
screws with washer (Fig. K5).
J-5 Spring
J-6 Cutting Line
J-8 Lower Housing ASSY
11
EN