Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Charging the Battery (Fig. B, C)
(HLVC315B Only)
WARNING:
charger.
From new, the rechargeable cells of the product need a
minimum charge time of 10 hours for HLVC315B to ensure
full power.
1. The switch must be in the OFF position, the appliance
will not charge if it is in any other position.
2. Fig C - Place the charging station
surface near a 120 Volt 60 Hz electrical outlet.
3. Place the appliance onto the charging station
shown in Fig. C.
nOTE: The appliance can then be stored on the charging
station
14
when not in use.
4. Plug the charger
15
electrical outlet.
5. The charge indicator LED
housing
4
will illuminate while charging.
6. The charge indicator LED
completion of charging.
nOTE: While charging, the charger may get warm,
this is perfectly normal and safe. It is safe to leave the
appliance connected to the charger indefinitely. The
charger automatically reduces power consumption when
charging is complete.
WARNING:
at ambient temperatures below 39°F (4°C) or above
104°F (40°C).
ASSEMBLY AND ADJUSTMENTS
WARNING:
serious personal injury, turn unit off and lock
off the tool before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Assembly (Fig. D)
1. Align the top of the extension tube
inlet
?
as shown in Fig. D.
2. Push the extension tube
locks into position.
3. Align the bottom of the extension tube
brush
?
as shown in Fig. D.
4. Push the bottom of the extension tube
brush
?
so it locks into position.
5. To remove an accessory, press the accessory release
latch
?
located on the vacuum inlet or the bottom
of the extension tube and gently pull the connected
accessory off.
For use only with the supplied
14
on a flat, stable
into any standard 120 Volt 60 Hz
13
on the center of the main
13
will turn off upon
Do not charge the battery
To reduce the risk of
7
with the vacuum
7
onto the vacuum inlet
7
with the floor
7
onto the floor
WARNING:
unit with the rear of the vacuum facing a wall so that
any inadvertent fall of the unit would contact a wall
and not people or pets.
OPERATION (FIG. A)
WARNING:
ELECTRIC SHOCK – USE INDOORS ONLY.
WARNING:
serious personal injury, turn unit OFF before
14
as
making any adjustments or removing/installing
attachments or accessories. An accidental start‑up
can cause injury.
WARNING:
Never use the vac without its filter ( 10 .
Switching ON and OFF (Fig. D)
1. To turn the vac on, slide the ON/OFF switch
the "I" position.
2. To turn the vac off, slide the ON/OFF switch
to the "O" position.
3. Return the product to the charger immediately after use
so that it will be ready and fully charged for the next
use. Ensure that the product is fully engaged with the
charger plug.
Extendable Suction Tool (Fig. A, E)
An extendable suction tool
1. Pull the extendable suction tool
into position.
2. The extendable suction tool can be opened by folding
the sides outward. There are multiple angles of operation
as shown.
3. To store the extendable suction tool into the nozzle
fold the sides inward together as shown and press the
stopping rib
4. Push the extendable suction tool into the nozzle until it
locks into position.
nOTE: If the extendable suction tool pulls completly out
from the dust bowl it can be pressed back in and will lock
?
so it
into position.
Accessory Tools (Fig. F)
This vacuum comes with two accessory tools.
‑
Brush
‑
Crevice tool
•
Either accessory tool can be fitted directly to the nozzle
as shown in Fig. F.
When not in use position the
TO REDUCE THE RISK OF
To reduce the risk of
Projectile/Respiratory Hazard:
7
is built into the nozzle
7
21
.
8
.
9
.
English
1
forward to
1
backward
6
.
outward until it locks
6
7
Tabla de contenido
