Tabla de contenido
Idiomas disponibles
Idiomas disponibles
discharged from the air vents, especially after cleaning
/ replacement of the filters as debris inside the unit can
be disturbed.
•
Leaks from battery cells can occur under extreme
conditions. If the liquid, which is a 20‑35% solution of
potassium hydroxide, gets on the skin (1) wash quickly with
soap and water or (2) neutralize with a mild acid such as
lemon juice or vinegar. If the liquid gets into the eyes, flush
them immediately with clean water for a minimum of
10 minutes. Seek medical attention.
SAVE THESE INSTRUCTIONS
Additional Safety Warnings
a ) Prevent unintentional starting. Ensure the switch
is in the off‑position before picking up or carrying
the appliance. Carrying the appliance with your finger
on the switch or energizing appliance that have the
switch on invites accidents.
b ) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with
another battery pack.
c ) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation
or burns.
d ) Do not use a battery pack or appliance that
is damaged or modified. Damaged or modified
batteries may exhibit unpredictable behavior resulting
in fire, explosion or risk of injury.
e ) Do not expose a battery pack or appliance
to fire or excessive temperature. Exposure to
fire or temperature above 266 °F (130 °C) may
cause explosion.
f ) Follow all charging instructions and do not
charge the battery pack or appliance outside
of the temperature range specified in the
instructions. Charging improperly or at
temperatures outside of the specified range may
damage the battery and increase the risk of fire.
g ) Have servicing performed by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the product
is maintained.
h ) Do not modify or attempt to repair the appliance
or the battery pack except as indicated in the
instructions for use and care.
Additional Safety Information
WARNING:
any part of it. Damage or personal injury could result.
WARNING:
Everyday eyeglasses are NOT safety glasses. Also use
face or dust mask if cutting operation is dusty. ALWAYS
WEAR CERTIFIED SAFETY EQUIPMENT:
Never modify the power tool or
ALWAYS use safety glasses.
•
ANSI Z87.1 eye protection (CAN/CSA Z94.3),
•
ANSI S12.6 (S3.19) hearing protection,
•
NIOSH/OSHA/MSHA respiratory protection.
WARNING:
power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to
the State of California to cause cancer, birth defects
or other reproductive harm. Some examples of these
chemicals are:
•
lead from lead‑based paints,
•
crystalline silica from bricks and cement and other
masonry products, and
•
arsenic and chromium from
chemically‑treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to filter
out microscopic particles.
Wear protective clothing and wash exposed areas
•
with soap and water. Allowing dust to get into your
mouth, eyes, or lay on the skin may promote absorption of
harmful chemicals. Direct particles away from face and body.
•
Use the appropriate dust extractor vacuum to remove
the vast majority of static and airborne dust. Failure
to remove static and airborne dust could contaminate the
working environment or pose an increased health risk to
the operator and those in close proximity.
•
Use clamps or other practical ways to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable and may
lead to loss of control and injury.
Air vents often cover moving parts and should be
•
avoided. Loose clothes, jewelry or long hair can be caught
in moving parts.
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz ....................... hertz
min ..................... minutes
or DC ...... direct current
...................... Class I Construction
(grounded)
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
A ......................... amperes
W ........................ watts
English
Some dust created by
or AC ........... alternating current
or AC/DC .... alternating or direct
current
...................... Class II Construction
(double insulated)
n o ....................... no load speed
n ......................... rated speed
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation
..................... wear respiratory
protection
..................... wear eye protection
..................... wear hearing
protection
5
Tabla de contenido
