Important; Additional Safety Instructions - Scheppach HC100dc Traducción Del Manual De Instrucciones Original

All parts must be correctly mounted and all
conditions must be fulfilled to ensure fault-free
operation of the electric tool.
– Damaged protective devices and parts must
be properly repaired or replaced by a recog-
nised workshop, insofar as nothing different
is specified in the operating manual.
– Damaged switches must be replaced at a cus-
tomer service workshop.
– Do not use any faulty or damaged connection
cables.
– Do not use any electric tool on which the
switch cannot be switched on and off.
15 Have your electric tool repaired by a qualified
electrician
– This electric tool conforms to the applicable
safety regulations. Repairs may only be per-
formed by an electrician using original spare
parts. Otherwise accidents can occur.

16 Important!

– For your own safety you must only use the
accessories and additional units listed in
the operating instructions or recommended
or specified by the manufacturer. The use
of mounted tools or accessories other than
those recommended in the operating instruc-
tions or catalogue may place your personal
safety at risk.
17 Noise
– Wear ear muffs when you use the compressor.
18 Replacing the power cable
– To prevent hazards, leave the replacement of
damaged power cables strictly to the manu-
facturer or a qualified electrician. There is a
risk of electric shock!
19 Inflating tires
– Directly after inflating tires, check the pres-
sure with a suitable pressure gauge, for ex-
ample at your filling station.
20 Roadworthy compressors for building site op-
erations
– Make sure that all lines and fittings are suit-
able for the maximum permissible operating
pressure of the compressor.
21 Place of installation
– Set up the compressor on an even surface.
22 Supply hoses at pressures above 7 bar should be
equipped with a safety cable (e.g. a wire rope).
Warning! This electric tool generates an electromag-
netic field during operation. This field can impair ac-
tive or passive medical implants under certain condi-
tions. In order to prevent the risk of serious or deadly
injuries, we recommend that persons with medical
implants consult with their physician and the manu-
facturer of the medical implant prior to operating the
electric tool.
 www.scheppach.com /  [email protected] /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

ADDITIONAL SAFETY INSTRUCTIONS

Safety instructions for working with compressed
air and blasting guns
• The compressor pump and lines can become
very hot during operation. Touching these parts
will burn you.
• The air which is sucked in by the compressor must
be kept free of impurities that could cause fires or
explosions in the compressor pump.
• When releasing the hose coupling, hold the hose
coupling piece with your hand. This way, you can
protect yourself against injury from the rebound-
ing hose.
• Wear safety goggles when working with the blow-
out pistol. Foreign bodies or blown off parts can
easily cause injuries.
• Do not blow at people with the blow-out pistol and
do not clean clothes while being worn. Risk of in-
jury!
Safety information for paint spraying
• Do not process any paints or solvents with a flash
point below 55° C. There is a risk of explosion!
• Do not heat up paints or solvents. There is a risk
of explosion!
• If hazardous liquids are processed, wear protec-
tive filter units (face guards). Also, adhere to the
safety information provided by the manufacturers
of such liquids.
• The details and designations of the Ordinance on
Hazardous Substances, which are displayed on
the outer packaging of the processed material,
must be observed.
• Additional protective measures are to be undertak-
en if necessary, particularly the wearing of suitable
clothing and masks.
• Do not smoke during the spraying process and/or
in the work area. There is a risk of explosion! Paint
vapors are easily combustible.
• Never set up or operate the equipment in the vicini-
ty of a fire place, open lights or sparking machines.
• Do not store or eat food and drink in the work area.
Paint vapors are harmful to your health.
• The work area must exceed 30 m
ventilation must be ensured during spraying and
drying. Do not spray against the wind. Always ad-
here to the regulations of the local police author-
ity when spraying combustible or hazardous ma-
terials.
• Do not process media such as white spirit, butyl
alcohol and methylene chloride with the PVC pres-
sure hose. These media will destroy the pressure
hose.
and sufficient
3
GB | 21