Homelite HBV-30A Manual De Utilización página 19

HBV-30A.qxd 2/18/02
GB
F D E I
FEATURES
mulcher
The blower is equipped with a mulcher feature that
efficiently reduces leaves at a 12:1 ratio.
ASSEMBLY
UNPACKING
This product requires assembly.
Carefully remove the tool and any accessories from
■
the box. Make sure that all items listed in the packing
list are included.
Inspect the tool carefully to make sure no breakage or
■
damage occurred during shipping.
Do not discard the packing material until you have
■
carefully inspected and satisfactorily operated the tool.
WARNING
If any parts are missing do not operate this tool
until the missing parts are replaced. Failure to do
so could result in possible serious personal injury.
WARNING
Do not attempt to modify this tool or create
accessories not recommended for use with this
tool. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious personal injury.
NOTE: Read and remove all hang tags and store with
your Operator's Manual.
WARNING
Stop the engine and disconnect the spark plug
wire before installing parts, making adjustments,
cleaning, or when not in use. Failure to do so
could result in possible serious personal injury.
ASSEMBLING THE BLOWER TUBES (Fig. 2)
Turn out the screw on the nozzle (9).
■
Screw the upper blower tube (10) onto the nozzle (9).
■
Tighten the screw on the nozzle (9).
■
Place clamp around the neck of the blower housing
■
outlet. Do not tighten the knob (12) yet.
Align the locking tab on upper blower tube with the
■
slot in the blower housing outlet; push the tube into
the housing. Twist to lock into place.
Rotate the tube so the nozzle is pointing upward as
■
shown. Tighten the knob securely.
To remove the tubes, loosen the knob on the clamp.
■
10:08 AM Page 13
P NL S DK N FIN GR HU
English
CZ RU RO PL SLO HR TR EST LT
Rotate the tubes to unlock them and remove from the
blower housing outlet.
INSTALLING THE VACUUM BAG (Fig. 3 - 4)
Remove the nozzle and upper blower tube from the
■
blower.
Unzip the vacuum bag (12) and place the adaptor
■
(15) inside as shown.
Align the locking tab on the bag adapter with the slot
■
in the blower housing outlet; push the bag adaptor
into the housing. Twist to lock into place.
Tighten the knob (20) securely.
■
Rotate the vacuum bag until the shoulder strap is
■
upright.
Make sure the vacuum bag is zipped and closed
■
before starting the unit.
WARNING
Stop the engine and disconnect the spark plug
wire before installing parts, making adjustments,
cleaning, or when not in use. Failure to do so
could result in possible serious personal injury.
INSTALLING THE VACUUM TUBES (Fig. 5 - 6)
To install the vacuum tubes:
Screw the upper and lower vacuum tubes together
■
and tighten securely.
Loosen the door screw (9) on the inlet cover door (10)
■
and open. Place the notch in the support arm (23) of
the upper vacuum tube under the hinge (21) of the
inlet cover door.
Push the upper vacuum tube into the blower housing.
■
Align the upper vacuum tube screw (22) with the hole
■
in the housing and tighten securely.
To remove the vacuum tubes:
Loosen the upper vacuum tube knob.
■
Remove the vacuum tubes from the blower housing.
■
Close the inlet cover door and tighten the door knob
■
securely.
OPERATION
WARNING
Petrol is extremely flammable and explosive.
A fire or explosion from gasoline will burn you
and others.
MIXING THE FUEL
This product is powered by a 2-stroke engine and
■
requires premixing petrol and 2-stroke oil. Pre-mix
unleaded petrol and 2-stroke engine oil in a clean
container approved for petrol.
13
LV SK BG