Technical Data - Black+Decker FSMH1321 Traducción De Las Instrucciones Originales

ENGLISH
Steam Cleaning with the mop
Fit hand held steam cleaner (5) to the steam mop body
u
(11)
Place a cleaning pad (13) on the floor with the velcro 'loop'
u
side facing up.
Lightly press the steam mop down onto the cleaning pad
u
(13).
Connect the steam mop to the mains.
u
Press the ON/OFF button (1). It takes approximately 20
u
seconds for the steam mop to heat up.
TM
Turn the Autoselect dial (2) until the required setting is
u
reached. After a few seconds steam will start to come out
of the steam head.
Note! When first filled or after running dry, it can take up to 45
seconds for steam to be produced.
It takes a few seconds for steam to enter the cleaning pad.
u
The steam mop will now glide easily over the surface to be
sanitized/cleaned.
Push and pull the steam mop slowly across the surface to u
thoroughly steam clean each section.
When you have finished using the steam mop, return
u
the handle (8) to the upright position, making sure that it
is supported and turn it 'OFF'. Wait until the steam mop
cools down (approximately five minutes).
Caution! It is important to monitor the water level in the
water tank. To refill the water tank and continue to sanitize/
clean stand the mop upright making sure that the handle is
supported and turn the steam mop 'OFF'. Unplug the unit from
the electrical wall outlet, and refill the water tank.
Caution! Never leave the steam mop in one spot on any
surface for any period of time.
Always place the steam mop with the handle (8) supported in
the upright position when stationary and make sure the steam
mop is turned off when not in use.
Carpet refreshing
Place a cleaning pad (13) on the floor with the 'loop' side
u
facing up.
lightly press the steam mop down onto the cleaning pad.
u
Place the carpet glider (12d) on the floor.
u
Lightly press the steam mop down onto the carpet glider
u
until it clicks into place.
Connect the steam mop to the mains.
u
Press the ON/OFF button (1). It takes approximately 20
u
seconds for the steam mop to heat up.
Turn the Autoselect TM dial (2) to the Wood/Laminate
u
setting.
Push and pull the steam mop slowly across the carpet to
u
thoroughly refresh each section.
When you have finished using the steam mop, return the
u
handle (8) to the upright position and turn the unit OFF.
Wait until the steam mop cools down (approximately five
minutes).
14
(Original instructions)
After use
dial (2) to the OFF position.
TM
Turn the Autoselect
u
Wait until the steam mop cools down.
u
Unplug the steam mop from the electrical wall outlet.
u
Empty the water tank.
u
remove the cleaning pad (13) and wash it ready for next
u
use (take care to follow the wash care instructions printed
on the cleaning pad).
Wrap the supply cable around the cable tidy hooks (7 and
u
9).
There is a hanging bracket (15) built into the hand grip (6)
u
which allows your steam mop to be hung from a suitable
hook on the wall. Always ensure that your wall hook is
capable of supporting the weight of the steam mop safely.
The handle also includes a rubber stopper which allows
u
your steam mop to be rested safely against a vertical
surface.
Hand held steam cleaning
Warning! Unit will not produce steam unless it is connected to
the main body (11) or the steam hose (16) is fitted.
Warning! Only use in a horizontal position.
Attach the required accessory.
u
Connect the hand held steam cleaner to the mains.
u
Press the ON/OFF button (1). It takes approximately 20
u
seconds for the steam mop to heat up.
Turn the Autoselect TM dial (2) until the required setting is
u
reached. After a few seconds steam will start to come out
of the steam head.
Note! When first filled or after running dry, it can take up to 45
seconds for steam to be produced.
When you have finished using the hand held steam
u
cleaner turn the Autoselect
Turn the unit OFF by pressing the ON/OFF button (1) and
disconnect from the mains supply. Wait until the unit cools
down before storing (approximately five minutes).
Accessories
The performance of your appliance depends on the accessory
used. BLACK+DECKER accessories are engineered to high
quality standards and designed to enhance the performance
of your appliance. By using these accessories you will get the
very best from your equipment.

Technical Data

Voltage Power
V W
ac
FSMH1321 230 1600
BHSM168D 230 1600
BHSM168U 230 1600
BHSM166DSM 230 1600
BHSM1615DSM 230 1600
dial (2) to the OFF position.
TM
Tank Heat-up Cable length Weight
Capacity time
ml secs m kg
≤20
500 6 2.7
≤20
500 6 2.8
≤20
500 6 2.8
≤20
500 6 2.8
≤20
500 7 2.9