Do not use the appliance. Inspect the seal on the SteaMitt
and hose If the seal is missing, damaged or any steam
is escaping then please contact your nearest authorised
repair agent. Do not use the appliance. Ensure there is no
blockage or impedence in the SteaMitt
hose. If any are detected then please contact your nearest
authorised repair agent. Do not use the appliance.
Fitting a cleaning pad to the
Warning! Ensure there is no blockage or impedence in
the steam release vents If any are detected then please
contact your nearest authorised repair agent. Do not use the
appliance.
Fit the cleaning pad (26) to the SteaMitt
u
attaching the 'loop' velcro strips (26a) on the upper side
of the cleaning pad, to the 'hook' velcro pads (24a) on the
underside of the SteaMitt
should not be used without fitting a
Warning! The SteaMitt
TM
cleaning pad.
Note: The SteaMitt
TM
accommodates 4 types of cleaning pads
of varying thickness. Scouring pad (for use on tough stains
and non delicate surfaces), Bathroom pad (for use on taps
and other moulded bathroom surfaces), Standard pad (for use
on all larger surfaces) and Polishing pad (for use on delicate
surfaces).
Warning! Always use the SteaMitt
@
figure K, with your hand inside the protective glove.
Warning! Never attempt to use the SteaMitt
@
gripping it externally as shown in figure L.
This will result in scalding.
Warning! Avoid using the SteaMitt
@
as shown in figure M.
Warning! Should a problem occur during use,
@
use the quick release tab to quickly remove the
from your hand as shown in figure N
TM
SteaMitt
Warning! Do not use the SteaMitt
@
such as windows as damage may be caused by the
sudden change in temperature.
Warning! Never point or direct the mitt at yourself
@
or any other person.
Note:
Variable steam dial is disconnected when the
is fitted and subsequently the flow of steam is
SteaMitt
TM
limited.
Use
Important! This unit will kill 99.9% of bacteria and germs
when used in accordance with the instructions in this manual
and with the micro fibre pads fitted and a continuous run time
of 90 seconds.
TM
hose or attachment
SteaMitt
TM
(Fig. J)
TM
(24) by
(24). Press down firmly.
TM
TM
as shown in
TM
by
TM
in tight corners
TM
on cold glass,
(Original instructions)
TM
Switching on and off
To switch the appliance on, press the ON/Off switch (1).
u
It takes approximately 20 seconds for the steam mop to
heat up.
To switch the appliance off, press the ON/Off switch (1).
u
Note: always have your hand inside the SteaMitt
press the steam button.
Caution! Never leave the steam mop in one spot on any
surface for any period of time.
Always place the steam mop with the handle (8) supported in
the upright position when stationary and make sure the steam
mop is turned off when not in use.
Caution! Always empty the steam mop after use.
Note! When first filled or after running dry, it can take up to 45
seconds for steam to be produced.
TM
Autoselect
Technology (Fig. P)
This steam mop is fitted with an Autoselect
shows various cleaning applications. They are used to select
the correct operating mode for your particular cleaning
operation.
TM
Using Autoselect
, choose from one of the following
applications by turning the Autoselect
required setting is selected.
Setting
Mop
Wood/Laminate
Tiles/Vinyl
Stone/Marble
The steam mop will select the correct volume of steam
required for your particular cleaning operation.
Note: Always check you are using the correct setting before
using your steam mop.
Hints for optimum use
General
Caution: Never use the steam mop without first attaching a
cleaning pad.
Always vacuum or sweep the floor before using the steam
u
mop.
The easiest way to use the appliance is to tilt the handle
u
to a 45º angle and clean slowly, covering a small area at a
time.
Use water only with no additives or chemicals with your
u
steam mop. To remove stubborn stains from vinyl or
linoleum floors, you can pre-treat with a mild detergent
and some water before using the steam mop.
ENGLISH
TM
before you
TM
dial (2) which
TM
dial (2) until the
Hand held
Low steam flow
Medium steam flow
High steam flow
13