Homelite F-2020 Manual De Utilización página 15

F 2020 _17 lgs 24/11/03
GB
F D E
SPECIFICATIONS
Engine Speed (rotational frequency)
at recommended max.
spindle rotational frequency
Engine speed (rotational frequency)
at idle
Fuel consumption (in accordance
with ISO 8893) at max.
engine performance
Specific fuel consumption
(in accordance with ISO 8893)
at max. engine performance
Vibration level idling
- Front Handle
- Rear Handle
Vibration level racing
- Front Handle
- Rear Handle
Sound pressure level
(in accordance with EN ISO 11806:
1997, ISO 7917:1987)
Sound power level (in accordance
with ISO 10884)
DESCRIPTION
1. SILENCER GUARD
2. CHOKE LEVER
3. THROTTLE CONTROL
AND REAR HANDLE
4. STARTER GRIP
5. THROTTLE TRIGGER
6. IGNITION SWITCH
7. DRIVE SHAFT HOUSING
8. FRONT HANDLE
9. GRASS DEFLECTOR
10. STRING HEAD
11. BOLT
12. FLAT WASHER
13. LOCK WASHER
14. WING NUT
15. BRACKET
16. TORQUE WRENCH
17. REAR HOUSING
18. SCREWS
19. BENT END OF
SILENCER GUARD
20. OPENING IN REAR HOUSING 42. MIXTURE NEEDLE
17:04 Page 11
I P NL S DK
English
INSTRUCTIONS
12,500/min -1
-1
3,100-4,300/min
0.48 kg/h
PACKING LIST FOR OWNER'S KIT
0.46 kg/h
2
4.8 m/s
4.8 m/s 2
2
13.0 m/s
2
8.4 m/s
GRASS DEFLECTOR (Fig. 2)
100 LpA (dBA)
1. Remove wing nut (14), flat washer (12), lock washer (13),
113 LwA (dBpA)
2. Place grass deflector over shaft and bracket (15).
3. Install bolt through the slots (29) in the tabs on grass
4. Install flat washer, lock washer and wing nut.
21. THROTTLE INTERLOCK
5. Tighten Securely.
22. PRIMER BULB
23. RUN POSITION
FRONT HANDLE (Fig. 3)
24. HALF CHOKE POSITION
25. CHOKE POSITION
1. Remove the front handle, bolt, and wing nut from the
26. SPOOL RETAINER
27. SPRING
2. Install the front handle onto the top side of the drive
28. SPRING
29. SLOTS
3. Place the bolt through the front handle as shown, then
30. EYELETS
31. DRIVESHAFT
32. ARROWS ON SPOOL
4. Tighten wing nut securely.
33. ANCHOR HOLE
NOTE: Do not attempt to remove or modify the spacer.
34. FIRST STRING
This spacer limits the upper position of the handle grip.
35. SLOT
36. SECOND STRING
37. LATCH
SILENCER GUARD ASSEMBLY (Fig. 4)
38. PULL COVER TO OPEN
39. FILTER
1. Remove silencer guard and two screws (18) from the
40. AIR FILTER COVER
41. IDLE SPEED SCREW
2. Attach the silencer guard to the rear housing (17).
NOTE: Make sure the bent end of the silencer guard (19)
fits securely into the opening of the rear housing (20).
3. Install two screws.
4. Tighten screws securely.
11
N FIN GR H
UNPACKING
Carefully remove the product from the carton.
Inspect the product to make sure no breakage or
damage occurred during carriage.
Do not discard the packing material until you have
inspected and operated the product.
Grass deflector (9)
Front Handle (8)
Silencer guard (1), torque wrench (16) and screws (18)
Fixings
Operator's manual
ASSEMBLY
and bolt (11) from the Owner's Kit.
deflector and bracket on driveshaft housing (7).
Owner's Kit.
shaft housing and move it to a comfortable position.
install the wing nut.
owner's kit.
CZ RUS RO PL