Wayne Dalton 8000 Manual Del Usuario página 13

8
NOTE: Refer to illustrations (A) or (B) to determine
Tools Needed:
which top bracket was supplied with your door.
Power Drill
Follow the corresponding step below:
7/16" Socket Driver
For Top Bracket (A): Align upper-center hole of the
top bracket base with #6 hole in the end stile (See
End Stile Hole Pattern on Pg 10). Ensure the top
bracket base is level and aligned with the edge of the
section. Secure the top bracket base to the endstile
using (4) 1/4" - 20 x 7/8" self drilling screws.
Loosely fasten the top bracket slide with 1/4"-20 x
5/8" carriage bolt and 1/4"-20 flange hex nut. Insert
a short shaft roller into the top bracket slide. The top
bracket slide will be adjusted and tightened in Step
18. Repeat for the opposite side.
For Top Bracket (B): Align upper-center hole of
the top bracket base with #6 hole in the end stile
(See End Stile Hole Pattern on Pg 10). Ensure the
top bracket base is level and aligned with the edge
of the section. Secure the top bracket assembly to
the endstile using (4) 1/4" - 20 x 7/8" self drilling
screws. Loosen the 5/16" - 18 nut on the top bracket
assembly. Insert a short shaft roller into the top
bracket slide. The top bracket slide will be adjusted
and tightened in Step 18. Repeat for the opposite
side.
NOTE: For windload specification option codes 1124,
1125, 1142 and 1144, do not insert a short shaft
roller.
For windload specification option codes 1124,
1125, 1142 and 1144 (C): Two top bracket
assemblies and a long shaft roller are required.
Loosen the 5/16" - 18 nut on the top bracket
assembly and position it flush against the stile,
and centered on the stile. Insert a long shaft roller
through both slides of the top bracket assembly's
to align. Secure the top bracket assembly to stile
using (4) 1/4" - 20 x 7/8" self drilling screws. The top
bracket slide will be adjusted and tightened in Step
18. Repeat for other side.
Please Do Not Return This Product To The Store. Contact your local Wayne Dalton dealer. To find your local Wayne Dalton dealer, refer to your local
yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com.
Top Bracket
(1) 5/16"- 18 x
5/8" Carriage bolt
and (1) 5/16"- 18
hex nut
#6 hole
End
stile
(1) 1/4"- 20 x 5/8"
Carriage bolt
(1) 1/4"- 20 Hex nut
Short shaft
roller
#6 hole
(1) 5/16"- 18 x 5/8"
Carriage bolt and (1)
5/16"- 18 hex nut
Short shaft
roller stile
Long shaft roller
(1320/1340 only)
Top bracket
base
Center hole
(4) 1/4"- 14 x 7/8"
Self drilling screws
(A)
Top bracket
slide
Top bracket
base
End
stile
(A)
section
Top bracket
assembly
Center hole
End
(4) 1/4"- 14 x 7/8"
Self drilling screws
(B)
Stile
Top bracket
assembly
(1) 5/16"- 18 x 5/8"
Carriage bolt and (1)
5/16"- 18 hex nut
(4) 1/4"- 14 x 7/8"
Self drilling screws
(C)
Top
section
Top
section
Top
13