General Operations - Blaupunkt SILVERSTONE C34 Manual Del Usuario

General Operations

Turning the power On
Press the PWR button to turn the unit On.
Turning the power Off
Press the PWR button for more than 2 seconds. Display will
revert to clock indication.
Tip
When you turn on the unit, "HELLO" will be displayed then
"WELCOME" will momentarily be displayed before actual
power on.
When you turn off the unit, "SEE YOU" will be displayed then
"GOOD-BYE" will momentarily be displayed before actual
power off.
You can edit these messages. (See "Turn on/off message edit").
Volume Control
Rotate the VOL dial to adjust the volume.
Volume down Volume up
Muting the sound
PWR
Press . The R-ch/L-ch Level Meter flashes.
To restore the previous volume level, press
Mute level can be adjustable. (See " Adjusting the Sound
Characteristics ")
Switching the Display
MENU
Press the to display the temporary indication (initial
setting is clock display) for few seconds. Then automatically
returns to the previous indication.
• Radio mode • AUX mode
Frequency or Clock. AUX title or Clock.
• Tape mode • CDC mode
Tape Status or Clock. CDC Status or Clock.
Setting the Clock
1.
Turn the ignition key to the ON position.
2.
PWR
Press the
3.
Press the MENU
play "CLK SET".
4.
Press the PWR
5.
Use the following buttons and dial to set the clock. (The blink-
ing section can be adjusted.)
PWR
or
6.
MENU
Press the
ting mode.
Ignition-off Clock Recall
The display will illuminate showing the time and then auto-
matically shut off after 5 seconds.
Press the MENU while the ignition switch is in the " OFF "
position.
Switching the Source
PWR again.
You can connect auxiliary equipment (Portable MD player,
etc) to this radio via optional AUX-IN cable.(See page 9)
Each time the SRC
change over as shown below;
Note
If the SRC button is pressed when no Tape has been loaded
into the unit, The Tape mode will skip to the AUX or CHANGER
mode.
to turn on the unit.
, then press the or to dis-
to enter the clock adjustment mode.
: To switch Hour/Minute blink
: Adjust the Hour and minute
momentarilfly to complete the Clock set-
is pressed, the operation source will
Adjusting the Sound Characteristics
1.
Press the MENU for more than 2 seconds to enter the
audio adjustment mode, then press the
to select the desired adjustment item as table below.
2.
Press the or or rotate the VOL dial to adjust
the selected item.
Use the following tables as a guide for adjusting the set-
tings in each item.Adjust within 5 seconds after selecting
the item. After 5 seconds, the unit returns to previous
indication.
or
Adjustment Range
EQ OFF (Equalizer will be displayed if set up)
BASS BAS –5 0
TREBLE TRE –5 0
LOUDNESS LOUD OFF
BALANCE BAL L9(Full left) 0
FADER FAD R9(Full rear) 0
ON VOL 0 50
20
MUTE 0
•A italicized letter is an initial value.
Tips
• EQ OFF (EQ Display)
Displays the current setting of equalizer curve, if the equal-
izer has been set. (See page 5)
• ON VOL (Limit volume)
Adjust the volume at the time of power on. You can adjust
with the actual sound.
• MUTE (Mute level)
You can adjust the mute level with the actual sound.
• Settings for BASS, TREBLE, and LOUDNESS can be made
to each of the following modes independently:
Each radio band, TAPE, CDC.
or
BAS +5
TRE +5
LOUD ON
BAL R9(Full right)
FAD F9(Full front)
80
80
E-3