Installation Hardware - Chamberlain POWER DRIVE GPD60 Manual Del Usuario

These safety alert symbols mean WARNING – a personal safety or property damage instruction.
Read these instructions carefully.
This garage door opener is designed and tested to offer reasonable safe service provided it is installed and operated in strict accordance with
the following safety rules.
Failure to comply with the following instructions may result in serious personal injury or property damage.
WARNING: If your garage has no service entrance door, an Outside Quick Release must be installed. This accessory allows
manual operation of the garage door from outside in case of power failure.
Keep garage door balanced. Sticking or binding doors must be
repaired. Garage doors, door springs, cables, pulleys, brackets and
their hardware are under extreme tension and can cause serious
personal injury. Do not attempt to loosen, move or adjust them. Call
for garage door service.
Do not wear rings, watches or loose clothing while installing or
servicing a garage door opener.
To avoid serious personal injury from entanglement, remove all ropes
connected to the garage door before installing the door opener.
Installation and wiring must be in compliance with your local building
and electrical codes. This is a class 2 double insulated product,
connesction to earth is not required or provided.
Lightweight doors of fiberglass, aluminum or steel must be
substantially reinforced to avoid door damage. The best solution is
to check with your garage door manufacturer for an opener installation
reinforcement kit.
The safety reverse system test is very important. Your garage door
MUST reverse on contact with a 40mm obstacle placed on the floor.
Failure to properly adjust the opener may result in serious personal
injury from a closing garage door. Repeat the test once a month and
make any needed adjustments.
This unit should not be installed in a damp or wet space.
Door must not extend over a public byway during
operation.
1
Before You Begin
This operator is suitable for sectional doors.
1. Look at the wall or ceiling above the garage door. The header bracket MUST be
securely fastened to structural supports.
2. Do you have a finished ceiling in your garage? If so, a support bracket and
additional fastening hardware (not supplied) may be required.
3. Do you have an access door in addition to the garage door? If not, an Outside
Quick Release Accessory is required.
2
Tools Required for Installation
3
Hardware Provided
ASSEMBLY HARDWARE
1. Square Head Screws
2. 8mm Carriage Bolt
3. Cable Pulley

INSTALLATION HARDWARE

7. 6mm Nut
8. Concrete Anchor
9. 6mm Lag Bolt
10. Clevis Pins
11. 6x25mm Hex Bolt
12. Wire Clips
13. Hex Screws
14. C-rail Bracket
Start by Reading These Important Safety Rules
4. Pin
(2)
5. 8mm Lock Nut
(1)
6. Pulley Bracket
(1)
15. Clevis Pins
(5)
16. Ring Fastener
(4)
(4)
17. Flat Washer
(2)
18. Anchor
(2)
19. Insulated Staples
(3)
20. 6x12mm Hex Bolt
(2)
(1)
WARNING
Fasten the child warning label adjacent to the lighted door control
button as a reminder of safe operating procedures.
Disengage all existing garage door locks to avoid damage to
garage door.
Any door control buttons (if installed) MUST be located where the
garage door is visible, but out of the reach of children. Do not
allow children to operate push button(s) or remote control(s).
Serious personal injury from a closing garage door may result
from misuse of the opener.
Activate opener ONLY when the door is in full view, free of
obstructions and opener is properly adjusted. No one should
enter or leave the garage while the door is in motion. Do not allow
children to play near the door.
Use manual release only to disengage the trolley and, if possible,
ONLY when the door is closed. Do not use the red handle to pull the
door open or closed.
Disconnect electric power to the garage door opener before
making repairs or removing covers.
This product is provided with a transformer and power supply cord of
special design which, if damaged, MUST be replaced by a
transformer from your local Chamberlain Anz distributor and
fitted by a specialist.
SAVE THESE INSTRUCTIONS
4
C C o o m m p p l l e e t t e e d d I I n n s s t t a a l l l l a a t t i i o o n n
As you proceed with the assembly, installation and adjustment procedures in
this manual, you may find it helpful to refer back to this illustration of a
completed installation.
(1) Cable Pulley Bracket
(2) Trolley
(3) Chain/Cable Assembly
(4) Rail
(5) Hanging Bracket
(6) Power Cord
(7) Opener
(1)
(1)
(1)
(2)
(4)
(1)
(2)
(10)
(1)
(8) Light Lens
(9) Manual Release
Rope & Handle
(10) Door Arm
(11) Door Bracket
(12) Header Bracket