Before Starting The Equipment; Mains Connection - HERKULES HES 105 OG Manual De Instrucciones Original

Read the operating instructions carefully before
using the welding set and follow them
Mains connection: ......................... 230 V ~ 50 Hz
Welding current: ......................................45-90 A
Duty cycle X%
Welding current I (A):
2
Rated idling voltage U
Max. welding wire drum: .............................0.4 kg
Welding wire diameter ............................. 0.9 mm
Fuse: ............................................................ 16 A
Weight: ........................................................14 kg
The welding times apply for an ambient tempera-
ture of 40° C.

5. Before starting the equipment

5.1 Assembly (Fig. 7-13)
5.1.1 Fitting the carrying strap (1)
Guide the carrying strap (1) through the slit on
the rear of the equipment, over the housing cover
(3) and through the slit on the front of equipment.
Connect the ends of the carrying strap as shown
in Figure 5 and adjust the strap to the required
length.
Fitting the welding screen (13)
•
Place the welding glass (l) and the transpa-
rent safety glass (m) over it in the frame for
the safety glass (k) (Fig. 7).
•
Press the safety glass retaining pins (q) into
the holes in welding screen frame (s) from the
outside. (Fig. 8).
•
Place the frame for the safety glass (k) with
the welding glass (l) and transparent safety
glass (m) from the inside into the recess in
the welding frame (s), press the safety glass
retaining bushes (n) on to the safety glass
retaining pins (q) until they engage to secure
the frame for the safety glass (k). The transpa-
rent safety glass (m) must be on the outside.
(Fig. 9).
•
Bend the top of the welding screen frame
(s) inwards (Fig. 10/1) and fold down the top
corners (Fig. 10/2) Now bend the outer sides
of the welding screen frame (l) inwards (Fig.
Anl_HES_105_OG_SPK7.indb 19 Anl_HES_105_OG_SPK7.indb 19
10 60
90 45
: ................................ 31 V
0
GB
10/3) and connect them by pressing the top
corners and outer sides together. When the
retaining pins engage, you should be able to
hear 2 clear clicks on each side (Fig. 10/4).
•
When the top corners of the welding screen
are connected as shown in Figure 11, place
the screws for the handle (p) from the outside
through the three holes in the welding screen.
(Fig. 12).
•
Turn over the welding screen and place
the handle (r) over the threads on the three
screws for the handle (p). Secure the handle
(r) to the welding screen using the three nuts
for the handle (o). (Fig. 13).

5.2 Mains connection

•
Before you connect the equipment to the
mains supply make sure that the data on the
rating plate are identical to the mains data.
•
The equipment may only be operated from
properly earthed and fused shock-proof so-
ckets.
5.3 Fitting the wire spool (Fig. 1, 2, 3, 14 – 22)
The wire spool is not supplied.
5.3.1 Wire types
Various welding wires are required for diff erent
applications. The welding set can be used with
welding wires with a diameter of 0.9 mm. The
appropriate feed rollers and contact tubes are
supplied with the set. The feed roller, contact tube
and wire cross-section must always match each
other.
5.3.2 Wire spool capacity
Wire spools with a maximum weight of 0.4 kg can
be fi tted in the welding set.
5.3.3 Inserting the wire spool
•
Unlock the housing cover (Fig. 1/3) by turning
the fastening screw (Fig. 6/12) through 90°
and flip open the cover.
•
Check that the windings on the spool do not
overlap so as to ensure that the wire can be
unwound evenly.
Description of the wire guide unit (Fig. 14-22)
A Wire spool
B Spool holder
C Guide tube
D Adjusting screw for roller brake
E Screws for feed roller holder
F Fee roller holder
G Feed roller
- 19 -
12.08.2015 17:59:23 12.08.2015 17:59:23