Nice MC424 Instrucciones Y Advertencias Para La Instalación Y El Uso página 14

Remote memorising
It is possible to enter a new transmitter in the receiver memory without using
the keypad. A previously memorised and operational remote control must be
available. The new transmitter will "inherit" the characteristics of the previously
memorised one. Therefore, if the first transmitter is memorised in mode I, the
new one will also be memorised in mode I and any of the buttons of the trans-
mitter can be pressed. If the first transmitter is memorised in mode II the new
one will also be memorised in mode II but the button activating the required
01. Press the button on the NEW transmitter for at least 5 seconds and then release
02. Press the button on the OLD transmitter 3 times slowly
03. Press the button on the NEW transmitter slowly and then release
Note – If there are other transmitters to memorise, repeat the above steps for each new transmitter .
4
DELETING ALL TRANSMITTERS
All the memorised codes can be deleted as follows:
01. Press the receiver button and hold it down
02. Wait for the Led to light up, then wait for it to switch off and then wait for it to flash 3 times
03. Release the button exactly during the third flash
Note – if the procedure was performed correctly, the Led will flash 5 times after a few moments.
WARNINGS: • All technical characteristics stated refer to an ambient temperature of 20°C (±5°C). • Nice S.p.a reserves the right to modify the product at any
timee, while maintaining the same functionalities and intended use. • The range of the transmitters and the reception capacity of the receivers may be subject to
interference that may alter their performance. In the event of interference, Nice cannot guarantee the effective capacity of their devices.
Receivers:
Decoding
Transmitter compatibility
Frequency
Input impedance
Outputs
Sensitivity
Working temp.
Transmitters:
Buttons
Power input
Absorption
Transmission frequency
Working temp.
Radiated power
Range
Dimensions / Weight
Encoding
12 – English
TABLE B3 - Remote Memorising
TABLE B4 - Deleting all transmitters
TECHNICAL CHARACTERISTICS OF THE PRODUCT
SMXI
Rolling code 52 bit FLOR
FLOR, VERY VR, NICE WAY, ERGO, PLANO, NICE ONE
433.92 MHz
52 KΩ
4 (on SM connector)
better than 0.5 µV
from -10°C to + 55° C
FLO2R
1, 2 or 4 according to the versions
12 V Batt. 23 A
10 mA
433.92 MHz
from -10°C to + 55° C
estimated approximately 1 mW E.R.P.
estimated 200 m (outdoors); 35 m (indoors)
69 x 39 x 15,5 mm / 31 g.
digital (4.5 x10 combinations)
15
output must be pressed on the first transmitter as must the button required to
be memorised on the second. You need to read all the instructions in advance
so you can perform the operations in sequence without interruptions. Now,
with the two remote controls (the NEW one requiring code memorisation and
the OLD one that is already memorised), position yourself within the operating
range of the radio controls (within maximum range) and carry out the instruc-
tions listed in the table.
SMXIS
Rolling code 64 bit SMILO
SMILO
433.92 MHz
52 KΩ
4 (on SM connector)
better than 0.5 µV
from -10°C to + 55° C
SMILO
2 or 4
12 V Batt. 23 A
25 mA
433.92 MHz
from -10°C to + 55° C
estimated approximately 1 mW E.R.P.
estimated 200 m (outdoors); 35 m (indoors)
Ø 48 mm x H 14 mm - 14 g
digital (18 x 10
x5s
TX TX
1s 1s
TX TX TX
TX
RX
RX
combinations)
15
1s
x1
x3
3°
x5