Transport; Cleaning And Maintenance; Storage; Electrical Connection - Scheppach BASA1 Traduccion Del Manual De Instrucciones Originale

11.1 Performing longitudinal cuts (Fig. 20)
Here, a workpiece is cut in its longitudinal direction.
• Position the longitudinal fence (25) on the left side
(if possible) of the Bandsaw blade (22), in accord-
ance with the desired width.
• Lower the saw band guide (5) onto the workpiece
(9.5).
• Switch on the saw (see 10.1).
• Press one edge of the workpiece against the lon-
gitudinal fence (25) with the right hand, whilst the
flat side lies on the saw bench (7).
• Slide the workpiece at an even feed rate along the
longitudinal fence (25) into the Bandsaw blade (22).
• Important: Long workpieces must be secured
against tipping at the end of the cutting process
(e.g. with reel-off stand, etc.)
11.2 Performing angled cuts (Fig. 19)
• Set saw bench to desired angle (see „Angled
cuts").
• Perform the cut as described under „11.1".
When producing angled cuts, only use the parallel
stop to the right of the saw band.
11.3 Freehand cuts (Fig. 21)
One of the most important features of a band saw is
the ease with which it can cut curves and radii.
• Lower the saw band guide (5) onto the workpiece
(see 9.5).
• Switch on the saw.
• Press the workpiece firmly onto the saw bench
(7) and slowly slide into the Bandsaw blade (22).
• In many cases it is helpful to roughly saw curves
and corners approximately 6 mm from the line.
• If it is necessary to saw curves that are too tight
for the saw band used, auxiliary cuts must be sawn
up to the front face of the curve, so that these fall
off as wood waste when the final radius is sawn.

12. Transport

The machine must only be lifted and transported on
its frame or the frame plate. Never lift the machine at
the safety devices, the adjusting levers, or the saw-
ing table.
During the transport the saw blade protection must
be in the lowest position and near the table.
Never raise at the table! Unplug the machine from
the mains during transport.

13. Cleaning and maintenance

WARNING! Prior to any adjustment, maintenance or
service work disconnect the mains power plug!
Cleaning
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible. Wipe
the equipment with a clean cloth or blow it with com-
pressed air at low pressure.
We recommend that you clean the device immedi-
ately each time you have finished using it.
30 GB
Maintenance
There are no parts inside the equipment which re-
quire additional maintenance.
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables.
Wear parts*: Bandsaw blade, Table insert, Push stick
* Not necessarily included in the scope of delivery!

14. Storage

Store the device and its accessories in a dark, dry
and frost-proof place that is inaccessible to children.
The optimum storage temperature is between 5 and
30˚C.
Store the power tool in original packaging.
Cover the electrical tool in order to protect it from
dust and moisture.
Store the operating manual with the electrical tool.

15. Electrical Connection

The installed electric motor is connected and is ready
to work. The connection complies with the relevant
VDE and DIN regulations. The customer-side mains
supply and the used extension line must meet these
regulations.
Important information
In the event of an overloading the motor will switch
itself off. After a cool-down period (time varies) the
motor can be switched back on again.
Defective Electric Connection Lines
Often, insulation damages occur on electrical con-
nection lines.
Causes are:
• Drag marks if connection lines are led through win-
dow or door clearances.
• Kinks due to improper attachment or routing of the
connection line.
• Cuts caused by running over the connection line.
• Insulation damages caused by pulling the connec-
tion line out of the wall socket.
• Fissures caused by the ageing of the insulation.
Such defective electric connection lines must not be
used and are hazardous due to the insulation dam-
ages.
Regularly check the electrical connection lines for
damages. Please make sure that the connection
lines are disconnected from the mains supply during
the check.
Electrical connection lines must comply with the rel-
evant VDE and DIN regulations. Only use connection
lines labelled with H05VV-F.
The labelling of the connection cable with the type
specification is required.