Generator Maintenance - Cebora JAGUAR MIG 2060/MD STAR DOUBLE PULSE Manual De Instrucciones

This welding machine
contemporarily mount 2 welding torches and 2 coils of
wire having a diameter of 300mm; this machine cannot
weld with the 2 torches at the same time, the torch
selection is made by means of selector switch D.
The gas cylinder must be equipped with a pressure
regulator and a gauge. If the cylinder is placed on the
cylinder shelf of the trolley, it must be fastened using
the strap provided. Only after positioning the cylinder,
connect the outgoing gas hose from the rear panel of the
machine to the pressure regulator.
2 gas hoses leave the rear panel, one is used in
combination with central adapter B and the other one
with central adapter B1. In order to select the right
combination read the plate at its side.
To make sure that the groove of the roller matches the
wire diameter used, open the mobile lateral side, remove
the cover CA, release the wire press roller by means of
the pressure adjusting knob BN, replace the roller and
remount the cover CA
BN
Fig. 4
Mount the wire coil and slip the wire into the feeder and
welding torch sheath.
Block the wire press roller with the knob BN and adjust
the pressure.
Turn on the machine.
Adjust the gas by means of key AY and then feed the wire
by means of key AW.
7 WELDING
Welding Synergic Pulsed MiG LED AP on.
Select the PRG number based on the wire diameter to be
used, the type and quality of the material, and the type of
gas, using the instructions located inside the wire feeder
compartment. Set the functions in the submenu according to the
instructions under paragraph «Service functions
5.2.3The welding parameters are set by means of knobAI.
Synergic MiG Welding LED AQ on.
Select the PROG number based on the wire diameter to be used, the type and quality of the material, and the
type of gas, using the instructions located inside the wire
16
has been designed
CA
to feeder compartment.
Set the functions in the submenu according to the
instructions under paragraph «Service functions
Adjust the wire speed and the welding voltage using the
knob AI.
Conventional MiG Welding LED AR on.
Select the PROG number based on the wire diameter
to be used, the type and quality of the material, and the
type of gas, using the instructions located inside the wire
feeder compartment.
Set the functions in the submenu according to the
instructions under paragraph «Service functions
Adjust the wire speed and the welding voltage using the
knob AI. and AN respectively.
8 ACCESSORIES
8.1 MIG WELDING TORCH ART. 1242
Air-cooled CEBORA MIG welding torch 280 A 3,5.
8.2 PUSH-PULL UP/DOWN WELDING TORCH, air
cooled, ART. 2003 and 2009.
8.3 Cooling unit Art. 1683
8.4 Water-cooled MIG torch Art. 1241
9 MAINTENANCE
Any maintenance operation must be carried out by
RVBMJßFE QFSTPOOFM JO DPNQMJBODF XJUI TUBOEBSE $&*
26-29 (IEC 60974-4).

9.1 GENERATOR MAINTENANCE

In the case of maintenance inside the machine, make sure
that the switch L is in position "O" and that the power
cord is disconnected from the mains.
Even though the machine is equipped with an automatic
condensation drainage device that is tripped each time
the air supply is closed, it is good practice to periodically
make sure that there is no condensation accumulated in
the water trap J
It is also necessary to periodically clean the interior of
the machine from the accumulated metal dust, using
compressed air.
9.2 PRECAUTIONS AFTER REPAIRS.
After making repairs, take care to organize the wiring so
that there is secure insulation between the primary and
secondary sides of the machine. Do not allow the wires
to come into contact with moving parts or those that heat
up during operation. Reassemble all clamps as they were
on the original machine, to prevent a connection from
occurring between the primary and secondary circuits should a wire accidentally break or be disconnected.
Also mount the screws with geared washers as on the
original machine.