DeWalt D55154 Manual De Instrucciones página 9

Fig. J
18
iMPORTAnT: The outlet being used must be installed and
grounded in accordance with all local codes and ordinances.
2. Ensure the outlet being used has the same
configuration as the grounded plug. DO nOT UsE
An ADAPTER.
3. Inspect the plug and cord before each use. Do not use if
there are signs of damage.
4. If these grounding instructions are not completely
understood, or if in doubt as to whether the compressor
is properly grounded, have the installation checked by a
qualified electrician.

DANGER: Risk of electrical shock. IMPROPER
GROUNDING CAN RESULT IN ELECTRICAL SHOCK.
• Do not modify the plug provided. If it does not
fit the available outlet, a correct outlet should be
installed by a qualified electrician.
• Repairs to the cord set or plug MUST be made by a
qualified electrician.
Extension Cords
Using extension cords is not recommended. The use of
extension cords will cause voltage to drop resulting in
power loss to the motor and overheating.
Instead of using an extension cord, increase the working
reach of the air hose by attaching another length of hose to
its end. Attach additional lengths of hose as needed.
If an extension cord must be used, be sure it is:
• a 3-wire extension cord that has a 3-blade grounding
plug, and a 3-slot receptacle that will accept the plug
on the product
• in good condition
• plug is not worn
• no longer than 50 feet (15,2 m)
• 12 gauge (AWG) or larger. (Wire size increases as gauge
number decreases. 10 AWG may also be used. DO NOT
USE 14, 16 OR 18 AWG.)
Voltage and Circuit Protection
Refer to the Voltage and Minimum Branch Circuit
Requirements under Specifications.

CAUTION: Certain air compressors can be operated
on a 15 amp circuit if the following conditions
are met.
• Voltage supply to circuit must comply with the
National Electrical Code.
• Circuit is not used to supply any other
electrical needs.
• Extension cords comply with specifications.
20
19
• Circuit is equipped with a 15 amp circuit breaker
or 15 amp time delay fuse. NOTE: If compressor
is connected to a circuit protected by fuses, use
only time delay fuses. Time delay fuses should be
marked "D" in Canada and "T" in the US.
If any of the above conditions cannot be met, or
if operation of the compressor repeatedly causes
interruption of the power, it may be necessary to
operate it from a 20 amp circuit. It is not necessary to
change the cord set.
Compatibility
Air tools and accessories that are run off the compressor
must be compatible with petroleum-based products. If you
suspect that a material is not compatible with petroleum
products, an air line filter for removal of moisture and oil
vapor in compressed air is required.
nOTE: Always use an air line filter to remove moisture and
oil vapor when spraying paint.
Location
Place the air compressor in a clean, dry and well ventilated
area at least 12" (30.5 cm) away from the wall or other
obstructions that will interfere with the flow of air. Keep the
compressor away from areas that have dirt and/or volatile
fumes in the atmosphere. These impurities may clog the
intake filter and valves, causing inefficient operation.
The air compressor pump and shroud are designed to
allow for proper cooling. The ventilation openings on the
compressor are necessary to maintain proper operating
temperature. Do not place rags or other containers on or
near these openings.
Place the air compressor on a flat surface resting on the
rubber feet.
Noise Considerations
Consult local officials for information regarding acceptable
noise levels in your area. To reduce excessive noise, use
vibration mounts or silencers, relocate the unit or construct
total enclosures or baffle walls. Contact a D
center or call 1–800–4-D WALT for assistance.
e
Electrical
Refer to all safety instructions before using unit. Observe
extension cord safety instructions if necessary. Always move
the On/Off switch 1 to the OFF position before removing
the plug from the outlet.
Transporting
When transporting the compressor in a vehicle, trailer, etc.
ensure that the air tank is drained and the unit is secured
and placed on a flat horizontal surface.
nOTE: Use recommended tie down points
transporting. Use care when driving so to avoid tipping the
unit over in the vehicle. Damage can occur to the unit or
surrounding items if unit is tipped.
Lifting
Always use two people when lifting and lift from the
recommended lift points
22
English
WALT service
e
21 when
.
7