Operation And Display Elements - Wolf Garten 700 Série Instrucciones De Funcionamiento

English
Do not smoke and keep burning
and hot objects away.
Store batteries in rooms which are
well ventilated and dry. There is
a risk of a possible short circuit
when working with the battery.
Do not place any tools or metal
objects on the battery.
Warning
Observe the order in which
the battery is mounted when
connecting/disconnecting the
terminals.
Fitting (Fig. 5a):
First connect the red cable

(+/positive pole) and then the
black cable (–/negative pole).
Removal:
First disconnect the black cable

(–/negative pole) and then the
red cable (+/positive pole).
Note
The battery is situated under the
passenger seat.
If a "maintenance-free/sealed"
battery (type 1) is supplied
(Battery without filler plugs)
The battery is filled with battery
acid and is sealed at the factory.
However, even a "maintenance-
free" battery requires maintenance
if it is to have a longer service life.
Keep the battery clean.

Avoid tipping the battery.

Electrolyte fluid leaks from
a 'sealed' battery, if it is tipped.
Before using the battery for the

first time, charge it using
a battery charger (max. charging
current 12 Volt/6 Ampere) for
1 to 2 hours. After charging the
battery, first pull out the battery
charger plug, then disconnect
the battery (see also operating
instructions for the battery
charger).
If an empty battery (type 2)
is supplied
(Battery with filler plugs)
Remove the filler plugs of the

battery cells (Fig. 5b).
Fill each cell slowly with battery

acid up to 1 cm below the filling
opening.
Let the lead in the battery absorb

the battery acid for thirty minutes.
Check the level of the battery

acid, add more if necessary.
Before using the battery for

the first time, charge it using
a battery charger (max. charging
current 12 Volt/6 Ampere) for
2 to 6 hours. After charging the
battery, first pull out the battery
charger plug, then disconnect the
battery (see also operating
instructions for the battery
charger).
Re-insert the filler plugs of the

battery cells.
Install the battery in the

appliance.
Remove the strip seal from the

battery vent. Connect the venting
hose so that the free end points
downwards in the appliance.
The hose must always allow free
passage (Fig. 5c)!
First connect the red cable (+),

and then the black cable (–).
Thereafter, use only distilled

water to top up the battery
(check every 2 months).
Keep the battery clean.

Operation and Display
elements
Warning. Damage to the
appliance.
The control and indicator functions
will be described to begin with.
Do not perform any functions at this
stage!
Ignition lock (depending
on model)
Fig. 6a
Start: Turn the key to the right
until the engine is running, then
release. The key rests at
Stopping: Turn the key to the left,
to .
Operating instructions for lawn tractors
Note
If the ignition lock features a light
position , the light is switched on
when the ignition key is moved
back to this position when the
engine has started.
Ignition lock with OCR
function (depending
on model)
Fig. 6b
This ignition lock features an OCR
function (= user-controlled mowing
in reverse gear).
Start: Turn the key to the right
until the engine is running, then
release. The key at
(normal) allows mowing in the drive
direction.
OCR position: Turn key to left of
normal position to reverse mowing
position
switch (1).
The indicator light (2) comes on
and indicates to the user that the
unit can now mow in reverse and
forward gear.
Stopping: Turn the key to the left,
to .
Note
Do not use the OCR function
unless absolutely necessary,
otherwise work with the key in the
normal position. The OCR function
switches off automatically as soon
as the key is turned to the normal
position or the engine is switched
off (stop position or disconnection
of the engine by the safety interlock
system).
Choke (depending
on model)
Fig. 7
To start a cold engine, pull the
choke (Fig. 7a), or move the
accelerator lever to
Throttle
.
Fig. 8
The engine speed can be adjusted
continuously. Fast engine speed
= . Slow engine speed =
and press the
(Fig. 7b).
.
7