Wolf Garten 700 Série Instrucciones De Funcionamiento página 12

English
Clutch/brake pedal (only for
models with Transmatic
drive)
Fig. 9
Engage = Depress pedal halfway.
Brake = Depress pedal all the way.
Note
Is also used to activate/deactivate
the parking brake.
Brake pedal
Fig. 9
Brake = Depress pedal.
Note
Is also used to activate/deactivate
the parking brake.
Direction of travel pedal
(only for models with
Transmatic drive)
Fig. 10
The direction lever must be used
only when the tractor is stationary.
To do this, depress the clutch/
brake pedal all the way and keep
depressed.
Forwards = lever to "F/ "
Idle = lever to "N"
Reverse = lever to "R/ "
Lever for setting the cutting
height
Fig. 11
Largest cutting height – cutters top
= lever to "5 (H)".
Smallest cutting height – cutters
bottom = lever to "1 (L)".
PTO lever
Fig. 12
The PTO lever actuates
a mechanism to switch ON and
OFF the cutters.
Switch off cutter deck 0/
pull lever all the way backwards
Switch on cutter deck I/
slowly press lever all the way
forwards
8
Parking brake for units with
hydrostatic drive/automatic
drive
Fig. 13
Actuating parking brake:
Fully depress brake pedal and
move lever to position "I".
Release parking brake:
Fully depress brake pedal and
move lever to position "0".
Lever for speed settings/
parking brake for units with
Transmatic drive
Fig. 14
Low speed = lever to "1".
High speed = lever to "6" or "7"
(optional).
Increase speed = adjust drive
positions without depressing the
clutch/brake pedal.
Reduce speed = adjust drive
positions by depressing the clutch/
brake pedal (depress halfway).
Actuating parking brake:
Fully depress clutch/brake pedal,
push lever for speed setting to
Release parking brake:
Fully depress clutch/brake pedal,
push lever to a speed setting.
Drive lever for units
with hydrostatic drive
(depending on model)
Fig. 15
Using the drive lever, set the speed
steplessly and change the driving
direction.
Forwards:
Fast forward driving = lever to
"F/ ".
Maximum mowing speed = lever to
" / ".
Stopping:
=
To stop driving and change
direction = lever to "N".
=
Reverse:
Reverse driving = lever to "R/ ".
Note
– The further the lever is pressed
towards "R" or "F", the faster the
unit moves.
Operating instructions for lawn tractors
– When the brake pedal is
actuated and released again,
the drive lever moves towards
the "N" position and reduces
the operating speed.
Accelerator for units with
hydrostatic drive (depending
on model)/automatic drive
Fig. 16
The drive pedal is used to adjust
the speed continuously and to
change direction:
Forwards = push forwards the drive
pedal (in direction
forward, the faster.
Stop (for stationary vehicle and
changing direction) = release the
drive pedal (N).
Reverse = push back the drive
pedal (counter to direction
the further back, the faster.
Note
When the parking brake is switched
on, the accelerator cannot be
actuated.
.
Gear release lever for units
with automatic drive
Fig. 17a
The lever is situated on the left side
of the unit between the footboard
and rear wheel.
For moving the appliance when
the engine is switched off:
Press lever inwards, then pull

outwards and swivel to the rear.
The lever is engaged in front of
the holder.
Driving:
Push the lever to the left and

press in.
Transmission release for
machines with a hydrostatic
drive
Units with drive lever
Fig. 17b
The lever is situated on the rear
panel of the machine.
For moving the appliance when
the engine is switched off:
Pull out lever and press to the

right.
), the further
),