Auxiliary Handle; Switching On/Off - Skil 9071 Manual De Instrucciones

o) Do not use accessories that require liquid coolants.
Using water or other liquid coolants may result in
electrocution or shock.
Kickback and related warnings
Kickback is a sudden reaction to a pinched or snagged
rotating wheel, backing pad, brush or any other accessory.
Pinching or snagging causes rapid stalling of the rotating
accessory which in turn causes the uncontrolled power tool
to be forced in the direction opposite of the accessory's
rotation at the point of the binding.
For example, if an abrasive wheel is snagged or pinched by
the workpiece, the edge of the wheel that is entering into
the pinch point can dig into the surface of the material
causing the wheel to climb out or kick out. The wheel may
either jump toward or away from the operator, depending
on direction of the wheel's movement at the point of
pinching.
Abrasive wheels may also break under these conditions.
Kickback is the result of power tool misuse and/or In correct
operating procedures or conditions and can be avoided by
taking proper precautions as given below.
a) Maintain a firm grip on the power tool and position
your body and arm to allow you to resist kickback
forces. Always use auxiliary handle, if provided, for
maximum control over kickback or torque reaction
during start-up. The operator can control torque
reactions or kickback forces, if proper precautions are
taken.
b) Never place your hand near the rotating accessory.
The accessory may kickback over your hand.
c) Do not position your body in the area where the
power tool will move if kickback occurs. Kickback will
propel the tool in the direction opposite to the wheel's
movement at the point of snagging.
d) Use special care when working corners, sharp
edges, etc. Avoid bouncing and snagging the
accessory. Corners, sharp edges or bouncing have a
tendency to snag the rotating accessory and cause loss
of control or kickback.
e) Do not attach a saw chain woodcarving blade or
toothed saw blade. Such blades create frequent
kickback and loss of control over the power tool.
Safety Warnings Specific for Polishing Operations:
a) Do not allow any loose portion of the polishing
bonnet or its attachment strings to spin freely. Tuck
away or trim any loose attachment strings. Loose
and spinning attachment strings can entangle your
fingers or snag on the workpiece.
Mounting the Protective Devices
▪
Before any work on the machine itself, pull the
mains plug.
AUXILIARY HANDLE
▪
For all work with the machine, the auxiliary handle
must be mounted.
Screw the auxiliary handle F into the head of the machine
according to the working method.
AUXILIARY HANDLE TYPE "D" (Figure 1) (Accessory)
Mounting the auxiliary handle type D K in the head of the
machine and fasten using the screw J. Use the allen key L
to fasten the screw J.
SKIL_IB9071_BR.indd 13
Mounting the polish tools
▪ Before any work on the machine itself, pull the mains
plug.
Use only accessories whose allowable speed is at least
as high as the no-load speed of the machine. SKIL will
not liable for problems arising from inadequate use or from
the assembly of accessories / devices or similar out of
specification, developed by third parties in order to attend
the client's specifics needs.
Clean the parts to be mounted.
Never press the button with the motor running,
!
for this will damage the transmission system.
Make sure the accessory is in perfect conditions.
Damaged
or worn out accessories do not produce well and damage
the workpiece.
RUBBER DISC
Lock the work spindle K by pressing the shaft lock A.
Assemble the rubber disc J on to the work spindle K and
screw it until the end.
To disassemble, press the shaft lock A and unscrew until
the end.
WOOL BONNET
Mount wool bonnet G about the rubber plate H.
For mounting, see the illustration page 2.
Starting Operation
Before connecting the plug into the any electric socket, be
sure that the voltage is the same as indicated on the toll's
name plate. The voltage in excess will increase the
accessory peripheral speed; reduced voltage reduces
speed too. In both cases the motor set will be damaged and
the end user will be explosed at hazards.
Tools with a rating of 230V can also be connected to a
220V supply.
SWITCHING ON/OFF
On/Off
Switching on: pressing the on-off switch E
Switching off: Release the on-off switch E.
Switch Locking
Locking: Pressing the on-off switch E together button D.
Switching off: Pressing and release the on-off switch E.
Test run! Check grinding tools before use. The grinding
tool must be properly mounted and turn freely. Perform a
test run for at least 30 seconds with-out load. Do not use
damaged, out of round or vibrating grinding tools.
Speed selector
Speed selector C has six speed levels numbered 1-6.
The speeds of these levels vary from 600 rpm (level 1) to
3.000 rpm (level 6). As it is a versatile tool with a wide
range of applications in different materials, and also to
avoid damaging the part to be worked, it is necessary to
select the speeds experimentally for each case before the
work is finally done.
13
30-3-2011 16:04:40