Makita DLS110 Manual De Instrucciones página 24

7KLV PLWHU VDZ HPSOR\V SRVLWLYH VWRS IXQFWLRQ <RX FDQ
VHW ƒ ƒ ƒ ƒ ƒ DQG ƒ ULJKWOHIW PLWHU
DQJOH TXLFNO\ 7R XVH WKLV IXQFWLRQ PRYH WKH WXUQ EDVH
close to your desired positive stop angle while holding
GRZQ WKH ORFN OHYHU 7KHQ UHOHDVH WKH ORFN OHYHU DQG
move the turn base forward until the turn base is locked.
Adjusting the bevel angle
NOTICE:
Always remove the upper guide fences
and vertical vise before adjusting the bevel angle.
NOTICE:
When changing bevel angles, be sure
to position the kerf boards appropriately as
explained in the "Kerf boards" section.
NOTICE:
When tilting the saw blade, be sure to
raise the handle fully.
NOTICE:
Do not tighten the knob too hard. Doing
so may cause malfunction of the locking mecha-
nism of the bevel angle.
1. 7XUQ WKH NQRE RQ WKH VOLGH SROH FRXQWHUFORFNZLVH
Fig.21: 1. Knob
2. Pull and turn the latch lever to the position as
illustrated.
Fig.22: 1. Latch lever
3. Match the pointer with your desired angle on the
scale by moving the carriage then tighten the knob.
Fig.23: 1. Bevel angle scale 2. Pointer
7R WLOW WKH FDUULDJH WR WKH ULJKW WLOW WKH FDUULDJH WR WKH OHIW
slightly and then tilt it to the right while pressing down
the releasing button.
Fig.24: 1. Releasing button
If you perform a bevel cut greater than 45°, move the
carriage while sliding the releasing lever toward the
IURQW RI WKH WRRO <RX FDQ SHUIRUP XS WR ƒ EHYHO FXW
Fig.25: 1. Releasing lever
7KLV PLWHU VDZ HPSOR\V SRVLWLYH VWRS IXQFWLRQ <RX FDQ
VHW ƒ DQG  ƒ DQJOH WR ERWK ULJKW DQG OHIW TXLFNO\
Set the latch lever in the position as illustrated and tilt
WKH FDUULDJH 7R FKDQJH WKH DQJOH SXOO WKH ODWFK OHYHU
and tilt the carriage.
Fig.26: 1. Latch lever
CAUTION:
After changing the bevel angle,
always secure the knob.
Slide lock
7R ORFN WKH VOLGLQJ PRYHPHQW RI WKH FDUULDJH SXVK WKH
carriage toward the guide fence until it stops. Pull the
stopper pin and rotate it 90°.
Fig.27: 1. Unlocked position 2. Locked position
3. Stopper pin
Switch action
WARNING:
into the tool, always check to see that the switch
trigger actuates properly and returns to the "OFF"
position when released. Do not pull the switch
trigger hard without pressing in the lock-off but-
ton. This can cause switch breakage. Operating a
tool with a switch that does not actuate properly can
OHDG WR ORVV RI FRQWURO DQG VHULRXV SHUVRQDO LQMXU\
WARNING:
operative switch trigger. $Q\ WRRO ZLWK DQ LQRSHU-
DWLYH VZLWFK LV +,*+/< '$1*(5286 DQG PXVW EH
repaired before further usage or serious personal
LQMXU\ PD\ RFFXU
WARNING:
by taping down or some other means. $ VZLWFK ZLWK
a negated lock-off button may result in unintentional
RSHUDWLRQ DQG VHULRXV SHUVRQDO LQMXU\
WARNING:
you simply pull the switch trigger without press-
ing the lock-off button. $ VZLWFK LQ QHHG RI UHSDLU
may result in unintentional operation and serious
SHUVRQDO LQMXU\ 5HWXUQ WRRO WR D 0DNLWD VHUYLFH FHQWHU
for proper repairs BEFORE further usage.
Fig.28: 1. Switch trigger 2. Lock-off button 3. Hole
for padlock
7R SUHYHQW WKH VZLWFK WULJJHU IURP EHLQJ DFFLGHQWDOO\
SXOOHG D ORFNRII EXWWRQ LV SURYLGHG 7R VWDUW WKH WRRO
press in the lock-off button and pull the switch trigger.
Release the switch trigger to stop.
$ KROH LV SURYLGHG LQ WKH VZLWFK WULJJHU IRU LQVHUWLRQ RI D
padlock to lock the tool off.
WARNING:
cable any smaller than 6.35 mm (1/4") in diameter.
$ VPDOOHU VKDQN RU FDEOH PD\ QRW SURSHUO\ ORFN WKH
tool in the off position and unintentional operation
PD\ RFFXU UHVXOWLQJ LQ VHULRXV SHUVRQDO LQMXU\
Electronic function
Constant speed control
7KH WRRO LV SURYLGHG ZLWK DQ HOHFWURQLF VSHHG FRQWURO
which helps maintain a constant blade rotation speed
HYHQ XQGHU ORDG $ FRQVWDQW EODGH URWDWLRQ VSHHG ZLOO
result in a very smooth cut.
Soft start feature
7KLV IXQFWLRQ DOORZV WKH VPRRWK VWDUWXS RI WKH WRRO E\
OLPLWLQJ WKH VWDUWXS WRUTXH
Laser beam action
For DLS111, DLS112 only
CAUTION:
Never look into the laser beam.
'LUHFW ODVHU EHDP PD\ LQMXUH \RXU H\HV
7R WXUQ RQ WKH ODVHU EHDP SUHVV WKH XSSHU SRVLWLRQ ,
RI WKH VZLWFK 7R WXUQ RII WKH ODVHU EHDP SUHVV WKH ORZHU
position (0) of the switch.
Fig.29: 1. Switch for laser
24 ENGLISH
Before installing the batteries
NEVER use tool without a fully
NEVER defeat the lock-off button
NEVER use the tool if it runs when
Do not use a lock with a shank or