Black and Decker BDDP100 Manual De Instrucciones página 3

17. REDUCE THE RISK OF UNINTENTIONAL STARTING.
Make sure switch is in "OFF" position before plugging in
power cord. In the event of a power failure, move
switch to the "OFF" position.
18. NEVER STAND ON TOOL. Serious injury could occur if
the tool is tipped or if the cutting tool is accidentally
contacted.
19. CHECK DAMAGED PARTS. Before further use of the
tool, a guard or other part that is damaged should be
carefully checked to ensure that it will operate properly
and perform its intended function – check for alignment
of moving parts, binding of moving parts, breakage of
parts, mounting, and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or replaced.
20. DIRECTION OF FEED. Feed work into a blade or cutter
against the direction of rotation of the blade or cutter
only.
ADDITIONAL SAFETY RULES FOR FOR DRILL PRESSES
WARNING: READ ALL INSTRUCTIONS BEFORE OPERATING PRODUCT. FAILURE TO FOLLOW
ALL INSTRUCTIONS LISTED BELOW MAY RESULT IN ELECTRIC SHOCK, FIRE AND OR SERIOUS
INJURY.
1. DO NOT OPERATE THIS TOOL UNTIL it is
assembled and installed according to the
instructions.
2. OBTAIN ADVICE from your supervisor,
instructor, or another qualified person if you are
not familiar with the operation of this tool.
3. FOLLOW ALL WIRING CODES and recommended
electrical connections.
4. NEVER START THE MACHINE BEFORE
CLEARING THE TABLE of all objects (tools, scrap
pieces, etc.).
5. NEVER START THE MACHINE with the drill bit,
cutting tool, or sander against the workpiece.
6. TIGHTEN ALL LOCK HANDLES before starting the
machine.
7. USE ONLY DRILL BITS, CUTTING TOOLS,
SANDING DRUMS, OR OTHER ACCESSORIES
that have shanks of 1/2in. in diameter or less.
8. USE ONLY DRILL BITS, CUTTING TOOLS, OR
SANDING DRUMS that are not damaged.
9. PROPERLY LOCK DRILL BIT, CUTTING TOOL,
OR SANDING DRUM IN THE CHUCK before
operating this machine.
10. USE RECOMMENDED SPEEDS for all operations.
11. AVOID AWKWARD OPERATIONS AND HAND
POSITIONS where a sudden slip could cause a
hand to move into the cutting tool.
12. KEEP ARMS, HANDS, AND FINGERS away from
the cutting tool.
13. HOLD THE WORKPIECE FIRMLY AGAINST THE
TABLE. Do not attempt to drill a workpiece that
does not have a flat surface against the table.
Prevent the workpiece from rotating by clamping it
to the table or by securing it against the drill press
column.
21. NEVER LEAVE TOOL RUNNING UNATTENDED.
22. STAY ALERT, WATCH WHAT YOU ARE DOING,
23. MAKE SURE TOOL IS DISCONNECTED FROM
24. THE DUST GENERATED by certain woods and wood
14. TURN THE MACHINE "OFF" AND WAIT FOR
15 PROPERLY SUPPORT LONG OR WIDE
16. NEVER PERFORM LAYOUT, ASSEMBLY, or
17 TURN THE TOOL "OFF", disconnect the tool
18. DISCONNECT THE TOOL from the power source,
19. ADDITIONAL INFORMATION regarding the safe
SAVE THESE INSTRUCTIONS.
3
TURN POWER OFF. Don't leave tool until it comes to
a complete stop.
AND USE COMMON SENSE WHEN OPERATING
A POWER TOOL. DO NOT USE TOOL WHILE
TIRED OR UNDER THE INFLUENCE OF DRUGS,
ALCOHOL, OR MEDICATION. A moment of
inattention while operating power tools may result in
serious personal injury.
POWER SUPPLY while motor is being mounted,
connected or reconnected.
products can be injurious to your health. Always
operate machinery in well ventilated areas and provide
for proper dust removal. Use wood dust collection
systems whenever possible.
SAVE THESE INSTRUCTIONS.
Refer to them often and use them to instruct
others.
THE DRILL BIT, CUTTING TOOL, OR SANDER
TO STOP TURNING prior to cleaning the work
area, removing debris, removing or securing
workpiece, or changing the angle of the table. A
moving drill bit, cutting tool, or sander can be
dangerous.
workpieces.
set-up work on the table/work area when the
machine is running.
from the power source before installing or removing
accessories, before adjusting or changing set-ups,
or when making repairs.
and clean the table/work area before leaving the
tool. LOCK THE SWITCH IN THE "OFF"
POSITION to prevent unauthorized use.
and proper operation of this tool is available from
the Power Tool Institute, 1300 Summer Avenue,
Cleveland, OH 44115-2851. Information is also
available from the National Safety Council, 1121
Spring Lake Drive, Itasca, IL 60143-3201. Please
also refer to the American National Standards
Institute ANSI 01.1 Safety Requirements for
Woodworking Machines and the U.S. Department of
Labor OSHA 1910.213 Regulations.