Alarm Codes - Selco Neomig 3500 Instrucciones De Uso

Permits adjustment of the length of the piece of wire
outside the torch.
Minimum off, Maximum 2.0s, Default 80ms
25 Spot welding
Allows you to enable the "spot welding" process and
establish the welding time.
Minimum 500ms, Maximum 99.9s, Default off
26 Pause point
Allows you to enable the "pause point" process and
establish the pause time between one welding opera-
tion and another.
Minimum 500ms, Maximum 99.9s, Default off
91 Reset XA (Advanced Mode)
0 Save and quit
Allows you to save the changes and quit the set up.
1 Reset
Allows you to reset all the parameters to the default
values.
3 Pre-gas
Allows you to set and adjust the gas flow prior to spark-
ing of the arc.
Permits filling of the torch with gas and preparation of
the environment for welding.
Minimum off, Maximum 99.9s, Default 10ms
4 Soft start
Permits adjustment of the wire feed speed in the phases
prior to sparking.
Given as a % of the wire speed set.
Permits sparking at reduced speed, therefore softer and
with fewer splashes.
Minimum 10%, Maximum 100%, Default 50%
5 Motor ramp
Allows you to set a gradual transition between the
sparking wire speed and the welding wire speed.
Minimum off, Maximum 1.0s, Default 250ms
18 Burn back
Permits adjustment of the wire burn time, preventing
sticking at the end of welding.
Permits adjustment of the length.
Permits adjustment of the length of the piece of wire
outside the torch.
Minimum off, Maximum 2.0s, Default 80ms
20 Post-gas
Permits setting and adjustment of the gas flow at the
end of welding.
Minimum off, Maximum 99.9s, Default 2.0s
25 Spot welding
Allows you to enable the "spot welding" process and
establish the welding time.
Minimum 500ms, Maximum 99.9s, Default off
26 Pause point
Allows you to enable the "pause point" process and
establish the pause time between one welding opera-
tion and another.
Minimum 500ms, Maximum 99.9s, Default off
92 Reset XP (Professional Mode)
0 Save and quit
Allows you to save the changes and quit the set up.
1 Reset
Allows you to reset all the parameters to the default
values.
3 Pre-gas
Allows you to set and adjust the gas flow prior to spark-
ing of the arc.
Permits filling of the torch with gas and preparation of
the environment for welding.
Minimum off, Maximum 99.9s, Default 10ms
4 Soft start
Permits adjustment of the wire feed speed in the phases
prior to sparking.
Given as a % of the wire speed set.
Permits sparking at reduced speed, therefore softer and
with fewer splashes.
Minimum 10%, Maximum 100%, Default 50%
5 Motor ramp
Allows you to set a gradual transition between the
sparking wire speed and the welding wire speed.
Minimum off, Maximum 1.0s, Default 250ms
18 Burn back
Permits adjustment of the wire burn time, preventing
sticking at the end of welding.
Permits adjustment of the length.
Permits adjustment of the length of the piece of wire
outside the torch.
Minimum off, Maximum 2.0s, Default 80ms
20 Post-gas
Permits setting and adjustment of the gas flow at the
end of welding.
Minimum off, Maximum 99.9s, Default 2.0s
25 Spot welding
Allows you to enable the "spot welding" process and
establish the welding time.
Minimum 500ms, Maximum 99.9s, Default off
26 Pause point
Allows you to enable the "pause point" process and
establish the pause time between one welding opera-
tion and another.
Minimum 500ms, Maximum 99.9s, Default off

3.2.2 Alarm codes

01/02 Overtemperature.
05 Secondary short circuit.
08 Wire feed motor blocked.
11 Machine configuration not valid.
14 Welding not possible with the step set.
20 Communication error.
21 Machine not calibrated or loss of data.
27