Important Charging Notes; Getting Started - Black and Decker BCD701 Manual De Instrucciones

Important Charging Notes

1. Longest life and best performance can be obtained if
the battery pack is charged when the air temperature is
between 65 °F – 75 °F (18 ° – 24 °C). DO NOT charge the
battery pack in an air temperature below 40 °F (4.5 °C),
or above 104 °F (40 °C). This is important and will
prevent serious damage to the battery pack.
2. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out the
lights;
c. Move the power adapter and battery pack to a
location where the surrounding air temperature is
approximately 65 °F – 75 °F (18 ° – 24 °C);
d. If charging problems persist, take the tool, battery
pack and USB cable to your local service center.
3. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily
done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may
also charge a partially used pack whenever you desire
with no adverse effect on the battery pack.
Transportation

WARNING: Fire hazard. Do not store or carry the
battery pack so that metal objects can contact
exposed battery terminals. For example, do
not place the battery pack in aprons, pockets, tool
boxes, product kit boxes, drawers, etc., with loose
nails, screws, keys, etc. Transporting batteries
can possibly cause fires if the battery terminals
inadvertently come in contact with conductive
materials such as keys, coins, hand tools and the
like. The US Department of Transportation Hazardous
Material Regulations (HMR) actually prohibit
transporting batteries in commerce or on airplanes in
carry-on baggage UNLESS they are properly protected
from short circuits. So when transporting individual
battery packs, make sure that the battery terminals
are protected and well insulated from materials that
could contact them and cause a short circuit.

CAUTION: GoPak battery terminal cap should be
used when battery is not connected to a power tool.
Terminal cap is provided for use whenever the battery
is out of the tool. Remove cap before placing battery
into tool.
FCC requirements for all digital devices
This device complies with Part 15 of the FCC Rules and Industry
Canada License-exempt RSS standard(s). Operation is subject to the
following two conditions:
1 . This device may not cause harmful interference, and
2 . This device must accept any interference
received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one of the following meaures:
ʵ Reorient or relocate the receiving antenna.
ʵ Increase the separation between the equipment
and receiver.
ʵ Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
ʵ Consult the dealer or an experienced radio/TV
technician for help.
CAN ICES-3(B)/NMB-3(B)

Getting Started

• The Micro USB port
in 1 battery is only to be used for charging the GoPak.
• The USB A port 11 on the BLACK+DECKER GoPak 2 in 1
battery is only to be used for powering USB devices
(Phone/Tablet/MP3/Wearable/Game Controller/etc.).
Fig. B
11
Charging the BLACK+DECKER GoPak 2 in 1
Battery (Fig. C, D)

WARNING: Never attempt to charge the
BLACK+DECKER GoPak 2 in 1 battery using the tool
terminals on the GoPak.

WARNING: You should only charge the
BLACK+DECKER GoPak 2 in 1 battery using UL or
CSA approved USB ports rated for charging high
performance devices. The GoPak can pull more
current than acceptable with older USB ports. An
error message may display on your computer if the
computer is used to charge the GoPak.
1. Plug the micro USB cable (included)
power supply (not included).
2. Plug the micro USB plug of your charger cord into the
GoPak micro USB port
on the BLACK+DECKER GoPak 2
12
13 into a USB
.
12
English
12
5